Question about Dishwashers

1 Answer

Hotpoint DWT10 Dishwasher error codes/lights

Hi

I have a DWT10 Hotpoint Dishwasher. It has the lights for the eco & fast programs flashing and will not drain. Any advice to what iit could be and how to fix it would be greatly appreciated.

Thanks

Posted by on

  • douglas_cord Apr 18, 2009

    i have a fridgadair gallery dishwasher mod# fdb737gfr3, the problem i am having is the other day all the lights went out and could not start. i disconnected and reconnected power so now i just have 2 lights flashing the high temp wash and no heat dry (lock) i tryed holding the lock for 3 seconds but still the two lights just flash























    9

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Food stuck in drain pump remove and clean out or scoop out - soak up all water then fill with 3 or 4 hot litres of water . cancel programme , start new one ( first thing unit does is switch to drain cycle ).
Then rock machine back and forth - this sometimes frees jammed debris thus pumping out of machine.
This works for me i have done it several times and it works

Posted on Feb 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Eco and fast wash lights flashing together and


this does mean draining cycle has timed out due to either blockage or faulty pump...

Dec 21, 2009 | Dishwashers

1 Answer

Hotpoint dwt10 not working rinse aid light flashing


I have DWT10P dishwasher.It is displaying two rapidly fashing E lights (Fast & Delicate )wash cycle.Can you tell me what its mean?

Mar 24, 2009 | KitchenAid 24 in. KUDI01IL - Multiple...

1 Answer

Hotpoint fwd60 eco and intensive lights flashing


Hi, I have a Hotpiont FWD60, the "delicate" lamp has started flashing about twice a second. Any ideas? Thanks, Nick

Mar 04, 2009 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Hotpoint Aquarius DWF50 Dishwasher, cycle not starting getting flashing ECO/Fast lights, any ideas?


hotpoint dwf50 will not start, the fast wash and prewash buttons are flashing together.

Jul 05, 2008 | Dishwashers

1 Answer

Hotpoint dishwasher bci450


Here are the eco related error codes for your washer..
1)Light 3 (eco) flashes. Water is present in the flood catching tray at the bottom which usually indicates that there is a leak somewhere. More often than not this is just a pipe with a poor fitting and simply tightening the clip is enough to stop the leak. Our machine had a very slow leak from one pipe (not enough to trigger the alarm) which was fixed in this way. The leak is detected by a small float switch located in the flood catch tray.

Undo 4 screws on the metal plate under the dishwasher 3 at the front 1 at the back, this reveals The pump check the seals are in place on the waste pump.

2) Wash indicator lights 3 + 5 (eco + pre) flashing rapidly. Filter is clogged. Pull out the filter and clean it.
3)Runs for approx. 3 minutes and then stops. Lights 3 + 4 (eco and fast) flash. Probably caused by being plumbed into a hot rather than cold water supply. The incoming water is hotter than required for the wash which causes the machine to cut out. Plumbing the machine into a cold water supply will fix the problem with no apparent long term problems.

May 23, 2008 | Hotpoint 18 in. BCI45 Slim-Line Built-in...

1 Answer

FDW60 Fast and Eco Lights


This is a bad control board that if replaced will only repeat in a short time .My advice is to contact the manufacturer and complain,you have the right as a consumer to do so.

Mar 17, 2008 | Hotpoint 24 in. FDW60 Free-standing...

2 Answers

Problemwith Hotpoint Aquarius FDW60


Eco light flashing, and refuses to do any of the other programs

Oct 15, 2007 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Flashing Lights


this error code is time out draining, check for a blockage

Jun 05, 2007 | Hotpoint 24 in. DWF34 Built-in Dishwasher

7 Answers

Dishwasher error codes please help


I too had this problen today. Printed off a manual from the Hotpoint website. Very helpful troubleshoot section. Anyway, flashing eco and fast lights and beeping sound indicates 'water feed pipe blocked' You need to check the water inlet connections on your tap.However, when we pulled it out we noticed the blue water inlet pipe was slightly kinked. Straightened this out and hey presto! It works fine again. How this happens when its worked ok for 18 months will never know but still. Try it! hope this was helpful...shewoo

Apr 26, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,731 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Brad Brown

Level 3 Expert

16993 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...