Question about Philips 55PP9401 55" Rear Projection Television

1 Answer

Need Service manual

After repair, slight convergence issue to adjust out .
Need a website to get Phlips manual.....Thanks.....T.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,130 Answers
Re: Need Service manual

No I am, sorry, I do not know. Those are hard top get if your not a warranty repair shop for Philips

Posted on Jan 25, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Samsung Projection TV - Yellow White Level and Auto Focus Failure

perfect focus is based on service mode convergence. FActory setting as it were. the set needs to converged in service mode then these values stored then it should work

Jan 03, 2008 | Samsung PCL541R 54" Rear Projection...

1 Answer

"Perfect Focus" problem on Samsung HCN4727W

You have a bad sensor, a bad digital convergence board, or the new board is not working correctly. I would start by swaping out the convergence board or exchange it for another one. Good Luck

Nov 08, 2007 | Projection Televisions

2 Answers

Sony kp-53xbr45 please let me know step by step how to enter convergence service thank you


To enter into the convergence service of your sony, follow the steps below;
  1. Press "Menu" on the remote control. Use the up- or down-arrow button to move the cursor to "Setup" and then press "Return."
  2. Use the up or down arrow to move the cursor to "Convergence" and press "Return." This will bring up the convergence-adjustment screen.
  3. Press the up or down arrow to move the cursor to the line you want to adjust (either vertical or horizontal for red and blue) and press "Return."
  4. Press the up or down arrow again to move that line until it converges with the center green line and press "Return."
  5. Repeat to adjust the other lines until all three lines converge and are seen as a white cross.
  6. Press "Menu" to exit the convergence menu and return to the original screen.
You can as well follow these steps;
  1. Press the "Power" button to turn your TV on.
  2. Wait at least 30 minutes before you adjust the convergence in your television. This allows your TV ample time to warm up before you make the adjustment.
  3. Turn your TV to a cable channel or to an antenna channel with a picture that you can see. A music channel with a static shot of music notes isn't the kind of picture you need. Instead, look for a picture like what you would see on a movie, sitcom or drama.
  4. Press the "Flash Focus" button located in the front panel on your TV. You may need to open a hidden compartment on the front of your TV to access this button. The convergence will repair itself automatically after you hit this button. It may take several minutes.
Any of the two processes are detailed steps on how to enter your convergence service.

Take care

Jul 03, 2010 | Sony KP-53XBR45 53" Rear Projection...

1 Answer

Convergence issue

You would have to go into the service menu to do fine convergence adjustments - The best way to approach this is to get a service manual - available online $ at - Also double check all the 3.9 ohm resistors near the convergence IC's

Nov 06, 2009 | Samsung HC-P4752W 47" Rear Projection...

3 Answers

RCA HD52W69D with a slight convergence & bowtie problem

Ur convergence it dead.If can't auto adjust must replaced.Tries Tv repair,Tv repair kits.

Nov 04, 2009 | RCA HD52W59 HDTV Projection Television

1 Answer

Convergence Issue on Toshiba TN50X81 - Service Manual & Parts Source?

Replace the convergence IC's - P/N STK192-110 with part STK192-150 or 180. Then you can go back in and make the detailed convergence settings and get your picture back in alignement. Also check the flame-resistant resistors around the ICs to make sure that none of them have opened up.

Jan 11, 2009 | Toshiba TN50X81 50" Rear Projection...

1 Answer

PT-47WX49 47 in. Rear Projectiopn Problem:

get in to the eprom setings and see if any adjustments have changed.the service manual can be gotton at

Aug 29, 2007 | Panasonic PT-47WX49 47" Rear Projection...

7 Answers

HC-P4752W - IC Replacement vs Convergence Module.

The colors weren't lining up correctly on my HC-P4752W which is only about 30 months old. I did a little bit of research and got ahold of the people at They recommended replacing the IC's as well as the IC resistors. I purchased the replacement parts from their site and made the repairs myself. I should mention that I didn't have any previous soldering experience. The repair was easy and a complete success. You may find replacement parts elsewhere for slightly cheaper but what you won't find is the prompt and detailed customer service that they provide. They gave me there # and said to call if I had any questions before or during repair. I took advantage of their services and got answers every time I called.

Aug 11, 2007 | Samsung HC-P4752W 47" Rear Projection...

1 Answer

Picture issues

It sounds like a convergence issue and possibly the amps themselves going out.. Cycling the unit off/on has me suspecting convergence amps first and possibly poor solder connections in the vert or convergence circuit. However, it could be one other thing, Vertical misadjusted. There is a methid for checking that in the service menu and I'll get to that in a second. The symptoms correcting themselves when you cycle on/off is very significant. I would first check for poor solder connections on the vert IC, and conv. amps. Then test the convergence amps themselves. If all else fails check the vertical adjustment. To adjust vertical enter service alignment mode by using 06-25-96 status, after entering service alignment mode it will be necessary to use the A/V button to get back to A/V4. When in the service alignment mode cursor down to GDE SAM. Cursor right and then cursor down to Geometry. Cursor right and then cursor down to VER. AMPL. then while watching the DVD in A/V4 cursor right or left to adjust the vertical amplitude until the white lines just disappear. Turn the set off to save the change. NOTE: Convergence may need to be touched up slightly after this adjustment has been made. Footnote: mnyce, this is one repair that I would not attempt unless you are fairly skilled at trace testing and knowing what to look for in a given circuit. As always, there are voltages in these areas that could harm you or further damage the unit. I would suggest contacting an honest qualified repair facility and explain your problem to them. Most will have no problem telling you exactly what I have here.. Goodluck. Bill

May 18, 2007 | Philips 55PW9383 55" Rear Projection...

Not finding what you are looking for?
Philips 55PP9401 55" Rear Projection Television Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66623 Answers

Are you a Philips Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides