Question about La Crosse Technology WS-8001-UM Digital Radio Controlled "Atomic" clock with Moon Phase&Indoor Tempe...

1 Answer

Outside Weather Not Displaying


The outside weather just shows dashes, not the temperature. I have replaced the batteries but it did not work. Do you have any suggestions?

My email is


Posted by on

1 Answer

Re: Outside Weather Not Displaying

Restart as if from new ie as if it is being taken out of the box

Posted on Jan 31, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


6 Points

Related Questions:

1 Answer


NOTE: Do not set the clock until the outdoor temperature is displayed. .... The unit will still try and receive the signal every day despite it being manually set. ..... sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes ... Beforesending the atomic clock in for repairs, contact La Crosse Technology.

La Crosse Technology Top Solutions
A: Complete a restart for display with the temperature/humidity sensor: ... to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing ... Products set outside of these time zones will not search for a WWVB signal as it is ... locate the Clock or Weather Display near an outside wall and point the unit in ...

Common issues weather stations: Click Here
Under £30 £30-£75 £75-£125 From £125 Birdhouses/Feeders Outdoor Clocks ... I'mnot getting any outdoor readings from my outdoor sensor, what do I do? This willcure 90% of all sensor connection problems, important you must ... is the airtemperature, to get this reading you need to place the unit away from direct sun.

Replacement Temperature Sensor ' AcuRite > All products

Dec 16, 2015 | Clock Radios

1 Answer

Remote sensor HMDX alarm clock with outside temperature not registering outside temperature

Is the remote very far from the clock? I find that some of these remotes don't have very good range. Try bringing the remote close to the clock to see if you can get them to connect. Some of these type remotes have a reset button or an opening that you can push a paper clip into to reset. I usually try to find a location close enough to the unit so it will connect by still try to keep it out of the weather. I also included a link to the instructions:

Jan 01, 2015 | Clock Radios

2 Answers

My Hammacher Schlemmer Projection Alarm Clock and Weather Monitor will not project the outside temp. It only projects the inside temp. How do I change? Also, can't change the time zone.

No solution but to return it...very annoying product but yet I like the projected display, very sharp and bright. The replacement was much better, it loses connection with outside transmitter often..but occasionally we see the outside temp

Dec 28, 2013 | Hammacher Schlemmer The Projection Alarm...

1 Answer

The outside temp is not displaying

If the clock uses a remote temperature transmitter, you may need to replace batteries.

Jan 12, 2013 | Sharp Atomic Weather Station Alarm Clock...

2 Answers

My AcuRite 00992 wireless weather station has suddenly quite displaying the outside humidity and dew point. Batteries are all new. I have lost my manual to troubleshoot this problem.

Double check the batteries to make sure they are installed correctly. If one of the batteries in the outdoor sending unit is in backwards, it will not send the outdoor data. On the indoor unit, there is typically one battery that is used for receiving the signal from the outdoor unit. If all of the batteries are in correctly but that one, you will see the display and the indoor temperature information, but the outdoor information will not be displayed.

Aug 27, 2010 | Acu-Rite Adagio Clock Radio

2 Answers

Outside temp. display

if it is wireless then check the sender unit
check the battery

severe cold weather can be hard on batteries

Jan 02, 2010 | La Crosse Technology WT-2171-UCS Digital...

10 Answers

Shift 3 Projection Alarm clock remote cannot open

Once the batteries are installed in the remote the temp will appear in the LED screen. Now you are ready to link signals between the main unit and the remote. Simply remove one of the two triple A batteries from the main unit and then replace. You should then see what appears to be a flashing object shaped like a kite with a tail while the two units link up. Then you should see the temp reading at the remote appear in the LED readout at the main unit. By the way there is also a very small reset at the top of the switches on the back of the main unit that can be depressed with a SMALL pointed object like a scissor point or safety pin point.

Feb 06, 2009 | La Crosse Projection Alarm Clock with...

2 Answers

Remote Sensor

make sure your time is set and the atomic clock time is recieved, then leaving the rear cover off of the transmitter, push the "tx" button not the "c/f" that is just for centegrade or ferenhight. you will see the red light on the front of reciever flash in a few seconds. The temp should display on your clock screen. If not, did the red l.e.d. light on transmitter flash. If not, its not sending data to clock. I have to reset and hit transmit every time I replace batteries on transmitter. Had no problems for over 2 years of using outside. If your not getting a reading with transmitter sitting next to clock after hitting "tx" button you may have defective transmitter.

Jan 13, 2008 | Homedics Sound Spa Premier SS-5000 Clock...

1 Answer

Remote Weather Station shows "HHH"

This means that the read is over the HIGH limit of the sensor, perhaps is too hot there. Change it to another location. josemaX

Jul 30, 2007 | GE 75295 Clock Radio

Not finding what you are looking for?
La Crosse Technology WS-8001-UM Digital Radio Controlled "Atomic" clock with Moon Phase&Indoor Tempe... Logo

1,607 people viewed this question

Ask a Question

Usually answered in minutes!

Top La Crosse Clock Radios Experts

The Knight
The Knight

Level 3 Expert

66352 Answers

William Dehn
William Dehn

Level 3 Expert

318 Answers

Pieter Vleeshouwers

Level 3 Expert

1315 Answers

Are you a La Crosse Clock Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides