Question about Adaptec (ASH-1233) (ASH1233) ATA Controller

2 Answers

Bios settings I am trying to add two LG sata DVD Burners and need to know how to setup the bios Thank Regards TC

Posted by on

  • 1 more comment 
  • Tangles Jan 27, 2008

    Thank you I have found that the Two Writer that I Have are LG GSA-H6-2N do not have Jumpers there is only the data in put and power no other these are the only writers I have found that does not have the jumper setting for the master or slave

    Regards Tangles

  • Tangles Jan 29, 2008

    Have found that Sata DVD writers do not have jumpers

    have set the bios and now find that can not do any thing with the two drives

  • Tangles Jan 30, 2008

    On my mother board there are two sata slots these have sata HD's connected

    The sata writers are connected via a addon board which has two sata slots and two IDE connection one has a hard drive connected

    The computer finds all driver and writers

    can not get the writers to read or write disc's

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 749 Answers

On your motherboard there are sata slots, usually there are two or four of them, Locate which is sata1, sata2, sata3 and sata4...
Connect them at sata2 and sata3, because sata1 is for the harddisk... The computer should automatically set things up right for you and also with the OS.

Hope this helps.

Posted on Jan 29, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 226 Answers

At bios settings choose auto detect for secondary master and secondary slave.

one burner must be master and the other one is slave jumper settings. all burners must be place at secondary drives.

Posted on Jan 24, 2008

  • earl llanera
    earl llanera Jan 29, 2008

    sorry i didnt know that you have SATA cables. ok.



    connect the drives in secondary sata cables. SATA's has automatic configurations.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Computer BIOS recognizes the SATA DVD Rewriter but Windows XP does not. The drive opens the loading door but it does not appear in the Windows XP explorer (My Computer).


Windows XP doesn't nativey support SATA. Check in BIOS to see if your motherboard supports sata to IDE emulation.
Comment back if you need further assistance.

Aug 17, 2011 | LG GH24LS50 Super Multi DVD±RW (±R DL) ...

2 Answers

My drive is not showing up in my computer nor it's not reading any cd/dvd


Simple test - try to boot from it. If you can't, or the unit isn't even recognized as present in the BIOS then it's dead - replace it.
If you can boot from it then the easiest way to fix the cause of this - a corrupted Windows registry - is to perform a Repair install.

Oct 01, 2010 | LG GH22NS50 22X DVDRW SATA Drive OEM...

1 Answer

Hl-dt-st rw/dvd gcc-4240n not working, does not read CD or DVD, I can hear the CD/DVD spin but that's all. Also, tried to uninstall and install the driver but no luck. I have a gateway Laptop with XP.


do it only if u r a professional..

open it up, with the lens assembly there is a small preset, turn it using a screw driver a little anti-clockwise..clean the lens with clean cotton using isopropyl alcohol..
if not done, replace the lens assembly..
or else, replace the drive with a standby n see..

i gotta know: is ur drive pata/sata and the device make n model..
assuming that ur drive is pata, n u r a professional n aware of bios/cmos setup utility handling..!!
open up ur system cabinet and see if all the data cables n jumper settings at the back of the drives (master/slave selection)..itz most important..!!
however, at the bootup (0.29sec) start pressing briskly the key to enter cmos utility or bios setup (eg. F1/F2/F10/Del as applicable)..glance in the standard settings if r detected individually..change the 'Mode' if m/b is hybrid type(both SATA+PATA) : Native/Compatible/Enhanced (as applicable)..
see if ur device needs any additional driver or not, if so try downloading..
also try checking itz data cable for loose or faulty..
above all explanation is applicable only if itz not being detected by the m/b or system..(not for reading or writing problem)..

contact ur system admin/vendor....

Nov 27, 2009 | LG GSA-T20N DVD±RW Dual Layer Burner

1 Answer

My LG CD/DVD player cannot read CDs anymore. Help!!!!


1st i gotta know: is ur drive pata/sata and the device make n model..
assuming that ur drive is pata, n u r a professional n aware of bios/cmos setup utility handling..!!
open up ur system cabinet and see if all the data cables n jumper settings at the back of the drives (master/slave selection)..itz most important..!!
however, at the bootup (0.29sec) start pressing briskly the key to enter cmos utility or bios setup (eg. F1/F2/F10/Del as applicable)..glance in the standard settings if r detected individually..change the 'Mode' if m/b is hybrid type(both SATA+PATA) : Native/Compatible/Enhanced (as applicable)..
see if ur device needs any additional driver or not, if so try downloading..
look if ur device itself is faulty by replacing with a standby..
also try checking itz data cable for loose or faulty..
above all explanation is applicable only if itz not being detected by the m/b or system..not for reading or writing problem....
contact ur system admin/vendor....

Nov 01, 2009 | LG GMA-4020B Super-Multi...

1 Answer

Trying to burn photos from dell laptop to DVD-RW blank disc . "error - no disk in drive"


Try another disc first ,if no luck than try another disc manufacturer. If it does not help check if you can play anything from this drive if no, check drive connection in your laptop you can also can check BIOS settings for this DVDRW drive and settings for IDE or Sata data transfer mode make shure it works in Ultra DMA not PIO mode. Be carefull with BIOS Setup!!! If nothing helps replace drive. Good Luck!

Jun 24, 2009 | Dell (7W036) DVD+RW Burner

1 Answer

New sata LG dvd room,it work correctly,but i can't boot from it


In your bios change the settings for boot order, 

1: DVD Rom
2: n/a
3: n/a
4...
5...
6...

This will force a boot off the only drive available which is the dvd rom. 

Apr 18, 2009 | Gigabyte GA-7VT600 1394 Motherboard

1 Answer

SATA RAID Controller Card Problem?


You are almost there. Go into your BIOS and enable RAID. Then your raid bios should show up on next boot.

Feb 15, 2009 | Intel Motherboard

1 Answer

I have a dell optiplex, the primary HD is a Western Digital 160gb Sata I also have a LG DVD/RW combo drive set to master on the IDE channel. I recently attempted to add a 2nd ide maxtor HD and for the...


Hi there
When you into the bios settings choose default bios settings and save, reboot the machine and have a look in the bios again to see if the bios has picked the drive up

Good luck and kind regards

Jan 07, 2009 | Computers & Internet

1 Answer

Installing windows without DVD


The hard disk is not recognized from USB because of SATA drivers not present on XP setup disk.

That happens because the BIOS uses a SATA controller that is not included in Windows XP install disk.

Usually you can solve the problem going to BIOS settings and changing SATA/RAID settings.Check your BIOS settings, and disable SATA RAID mode.This is done in different ways depending on the BIOS.

On HP/Compaq computers for example you press F2 on startup to enter BIOS, then disable SATA mode on bios settings.
On other makes the procedure can be slightly different.


Another way to fix the problem, is by creating your own XP setup disk with SATA drivers included, see:
Resolving "Setup did not find any hard disk drives" during Windows .

Mar 17, 2008 | Toshiba Portege M205-S810 Tablet PC

6 Answers

Problems Installing my 160 GB Seagate SATA HDD


Check the SATA/RAID controller setting. It could have been set to [Disabled] Refer to your user?s manual for a detailed description on how to enable the onboard SATA/RAID controller by adjusting the jumper or BIOS settings. Regards SparkGap

Sep 24, 2007 | ASUS P5RD1-VM Motherboard

Not finding what you are looking for?
Adaptec (ASH-1233) (ASH1233) ATA Controller Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Adaptec Computers & Internet Experts

Rommel Balcita

Level 3 Expert

749 Answers

Martin Murray

Level 3 Expert

1623 Answers

Robert Graf

Level 2 Expert

238 Answers

Are you an Adaptec Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...