Question about Dehumidifiers

1 Answer

Adjusting dehumidifier on furnace

Can't locate an adjustment knob/switch/vavle for the buit-in dehumidifier on my furnace. GMC GMPN060-3

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 828 Answers

This model furnace does not come with a built in humidifier. Humidifiers are normally an optional add on. If you have a by-pass type humidifier it is none adjustable. Water level is normally float controlled and operation is control by blower circuit. When ever the blower runs the humidifier operates when in the heating mode.

Posted on May 05, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, why does my dehumidifier goes on and off every 4 minutes, last year was working fine, started the machine last week ans now it goes on and off, thanks


Serge,
Most dehumidifiers work on a thermostat, and yours probably got turned down. You might look on the top and see if there are any knobs and try to adjust it that way.

May 26, 2015 | Dehumidifiers

1 Answer

How do i replace the humidity sensor


Only two wires and two screws. Shut off the furnace disconnect switch before doing anything. Then Pull off the cover and I do mean pull off. Then undo the two screws remembering what terminal they go to. Remove the screws from the back plate and let the wires fall through the back plate as you pull it off the wall or duct. Put the new back plate in place with the wires pulled thought. Install the screws I the same place as the old ones. Re attach the wires into the same labeled terminals as the old one. Put the new cover on. Turn on the furnace disconnect switch and away you go. To check operation all you need to do is, turn the knob on the humidifier control and listen for the solenoid to open and water to flow to the humidifier. If nothing happens then you need to check for power to the humidistat. Should be 24v. If no power then you need to check the source.


good luck

Apr 19, 2014 | Dehumidifiers

1 Answer

Dehumidifier runs continuously and displays higher than normal humidity levels.


Probably some glitch with the sensors. I recommend taking it to a service center.

Dec 06, 2013 | Haier DE65EK 65 Pints eco-Friendly...

1 Answer

Water overflows when filled how do I adjust?


Remove the tank and locate the switch and 'teeter' (that the tank sits on). Make sure the tank is able to move when filled. You will have to adjust the position of the switch to allow the filled (teetered) tank to shut the device off.

Is it possible for you to drain the water into a nearby floor drain using a hose?

Thanks for your question @ FixYa.com

Jun 26, 2011 | Goldstar DH2510A Dehumidifier

1 Answer

It won't start. Turning the knob, I don't hear the


Hi,
There are many reasons why a dehumidifier willnot work or collect water.
Here is a tip that I wrote to help people to figure out what is going wrongwith their dehumidifier

Dehumidifier is running but no water is in bucket

heatman101

;'
';';
';';';
;''';';

Jun 06, 2011 | Dehumidifiers

1 Answer

My new LG "ld450eal" DeHumidifier


The switch that says 'Bucket is full' is not adjusted properly.
It will need to be adjusted, normally a screw driver or pliers,
so that when its empty the switch is not made or the contacts
are open.
If it is in adjustment properly, then the switch is bad and needs
replacing.
Before you replace it, check to make sure the wires leading to it
are not touching, it may be sending a signal meaning 'full' by
electricaly touching each other at the switch.

Feb 25, 2011 | LG Dehumidifiers

1 Answer

Dehumidifier only runs for a few minutes then turns off. Model# AHG30


there is a knob on the machine that sets the level of humidity. it sounds like you need to adjust it to remove more humidity from the air before it shuts down.

Aug 28, 2009 | GE AHG50LB / AHG50LD Dehumidifier

1 Answer

Maytag electronic dehumidifiers full light stays on


Take out the bucket and locate the "full" switch in the upper right of the area where the bucket slides in. With the unit on, try pushing it in and see if the "full" light goes off.
If so, that switch is fine - if not try to adjust if and replace it if required. Those are generally micro-switches and firms like Radio Shack would have if your appliance parts dealer does not.

Aug 03, 2008 | Maytag M7DH45B2A Dehumidifier

Not finding what you are looking for?
Dehumidifiers Logo

Related Topics:

565 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dehumidifiers Experts

Bill Long

Level 3 Expert

588 Answers

Gil Shultz

Level 3 Expert

3382 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Are you a Dehumidifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...