Question about GE Energy Star WCVH6260F Front Load Washer

1 Answer

My washer keeps stopping at each cycle

My washer stopps inbetween each cycle and the start button begins to blink. I have to push the start button again to get it going. It doesn't finish washing, spinning or anything unless you are right there to push start again. Sometimes it makes a strang hum right before it's going to spin and just stops. Can anyone help with this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

And pl rate me if helped.

Posted on Jan 24, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Duet washer keeps stopping but restarts when I push start button.


usually a out of balance problem check to see if washer is level and not wobbly check the front and both sides with a level

Oct 20, 2014 | Whirlpool duet Washing Machines

1 Answer

Clean tub options keeps blinking on affinity frigidaire fafs4474lwo model


Hello Jodi, thank you for your post!

Your Frigidaire washer (FAFS4474LW0) will automatically prompt you to run the CLEAN WASHER cycle typically every 50 cycles. If you wish to begin the cycle, press SELECT when prompted. This maintenance cycle uses hot water and two rinses to remove residue that may cause odor. For best results, I recommend to use the CLEAN WASHER cycle once a month

You may press the CANCEL button to manually perform the cycle at another time if you prefer. You can do this by following these directions:

    ·Rotate cycle knob to Rinse & Spin
    ·Then press the CLEAN WASHER option button
    ·The LCD screen will display "SYSTEM CLEAN"

    Hope this helps! - Z

Jul 19, 2014 | Frigidaire Fafs4474lw Affinity 3.81 Cu Ft...

1 Answer

My washer had 1 minute left before the spin cycle was complete.


Push and hold the START button for three seconds if you want it to finish off that last minute.

...or...

Push and hold the PAUSE button for three seconds to stop the cycle.

Peace.

Marco

Jan 31, 2009 | Kenmore Elite 45986 Front Load Washer

2 Answers

GE Adora front load washer overloaded now won't start


Washers - Resetting Electronic Controls on a Washer

If there is a pause in the washer cycle, the controls will lock up. The pause can occur because of a power failure or it was put in the test mode at the factory.

Also, if the washer was stopped before the cycle was complete or the consumer has pushed the stop/pause button to temporarily stop the cycle and the cycle is not reset. Over a period of 24 hours, the washer will pump out and spin, but will stay in the final spin.

To correct the situation, shut off the circuit breaker for 30 seconds or unplug the washer, then turn the timer knob around and back to any position other than final spin. Verify the water is turned on and restore power. This should resolve the issue.

Apr 23, 2008 | GE WSXH208A Front Load Washer

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

2 Answers

Kenmore front load washer won't start. Lights just blink


I had same problem........push options and select button at same time, hold for 5 sec.......choose option.....machine stuck inbetween cycles.

at least it worked for me!

Dec 26, 2007 | Washing Machines

Not finding what you are looking for?
GE Energy Star WCVH6260F Front Load Washer Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...