Question about HP LaserJet 1320 Printer

4 Answers

Hp laserjet 1320 problem

When I power up the printer it doesn't go into its initialisation routine - the toner light is off, the attention light in on, and the ready & go lights are flashing. The printer will not respond to any buttons being pushed.

please help

Posted by on

  • Anonymous Feb 16, 2008

    when the printer is powered on all the lights come up except catridge indicator after a few seconds the first two green lights will be flashing, none of the buttons is responding. the catridge was removed and inserted into another printer which works well. the voltage was checked and there is no problem on the power unit. i even gave it to technicians but the problem persists, in my view i think that it might be a software problem. kindly help me with the service manual and other information that can help me out.

    kenny

  • Anonymous Mar 29, 2014

    when i turned on my printer it got initialize and showing attention light

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 51 Answers

This is an error state that is not described at HP site.

Try to do a hard reset:

1) Turn off the printer

2) Press and hold down the green GO button

3) Turn the printer on and continue to hold the green GO button for at least 5 seconds, but not longer than 15 seconds. During the process, the Attention LED will turn on.

4) Release the GO button.NOTE: If both the Attention light and the Ready LEDs turn on before the GO button is released, the cold reset procedure must be started over at step 1.

5) The printer LEDs begin cycling. The cold reset process runs until completion and the printer returns to the Ready state.

Hope it will help you

Posted on Jan 24, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I cant figure out what the **** is wrong

Posted on Jan 22, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 167 Answers

Try to remove cartridge and turn on the printer!!! If work initialisation routine put the cartridge back!!! Seek for the paper leftovers or paper jam in tray or back door!!! Or just do what say's Nubar

Posted on Jan 24, 2008

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Got exactly the same problem! I have no idea what to do, have reinstalled all software, checked for paperjam and all the simple things.

Have you guys yet figured out what's bothering the printer?

Posted on Sep 05, 2010

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

SOURCE: Laserjet 1320 shows undocumented light pattern, won't respond

paper jam

Posted on Nov 20, 2007

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1102 reser counter


  • I take it you are refilling the toner cartridge...
  • Switch the printer off.
  • Press and hold the green button on your printer and turn the printer on. You will see that the lights flash for a moment and then turn off. After a few seconds, the attention light will turn on followed by ready light and the green light. Keep pressing the green button. In a few seconds, the attention light and the ready light will turn off.
  • Push the toner rotate button while you continue pressing the green button. As you briefly push the toner button, you will see the light flashing. Release both the toner button and the green button.
  • Repeatedly push the red button (cancel button). Now all the working lights on the printer will turn off.
  • Open and close the lid of HP printer once. The light will start blinking.
  • Press the green button. Your HP toner cartridge chip will be reset.
  • Apr 25, 2014 | HEWLETT-PACKARD Hewlett Packard P1102...

    1 Answer

    Hp laserjet 1320 toner empty?


    you might try a recycled cartridge and have a lot less invested.Sounds like your cartridge is empty.Is print quality bad or light?

    Mar 20, 2014 | HP LaserJet 1320 Printer

    1 Answer

    Is not working more


    Switch the printer off.

    Press and hold the green button on your printer and turn the printer on. You will see that the lights flash for a moment and then turn off. After a few seconds, the attention light will turn on followed by ready light and the green light. Keep pressing the green button. In a few seconds, the attention light and the ready light will turn off.

    Push the toner rotate button while you continue pressing the green button. As you briefly push the toner button, you will see the light flashing. Release both the toner button and the green button.

    Repeatedly push the red button (cancel button). Now all the working lights on the printer will turn off.

    Open and close the lid of HP printer once. The light will start blinking.

    Press the green button. Your HP toner cartridge chip will be reset.

    Jan 29, 2013 | HP DeskJet F4280 All In One Printer InkJet

    1 Answer

    When printer is turn on that time printer reddy and cartridge light on so what is the problem


    You can see four LED's on control panel, from top to bottom,1st is toner indication 2nd Attention 3rd is Ready light, 4th go light.. Observe led's are 'blinking' or 'On' condition.. # If toner light is blinking ="toner cartridge missing or contact problem or memory faulty.
    # If toner light & ready lights are on= "toner low indication or refilled cartridge loaded".

    Jul 12, 2012 | HP LaserJet P2015dn Printer

    3 Answers

    HP 1320 Prints Blank Pages


    HP 1320 Prints Blank Pages Problem with the HP LaserJet 1320 Printer

    Sep 03, 2011 | HP LaserJet 1320 Printer

    1 Answer

    Brand new on power up attention light continually flashes and message says Please wait (Adding toner) and stays there forever


    It is normal to do this "adding toner" operation aprox. 20 minutes. You have to wait until the printer enters in "ready" status. Take a little brake and relax, your printer needs to fill/refill the developer unit with toner dust from the cartridge.

    Feb 16, 2011 | Kyocera FS2020D ECOSYS Monochrome Laser ...

    1 Answer

    What do symbols on top mean?


    Welcome to Fixya

    Half circle symbol means printer is in ready state. The printer control panel is comprised of six lights and two buttons. The lights produce patterns that identify the printer status.

    1 Jam light: Indicates that there is a jam in the printer.
    2 Toner light: When the print cartridge is low, the Toner light illuminates. When the print cartridge is out of the printer,
    the Toner light blinks.
    3 Paper out light: Indicates that the printer is out of paper.
    4 Attention light: Indicates that the print-cartridge door is open or other errors exist.
    5 Ready light: Indicates that the printer is ready to print.
    6 Go button and light: Initiates action or indicates status.
    7 Cancel button: To cancel the print job that is currently printing, press the Cancel button.

    Thank you for using Fixya!

    If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

    Feb 08, 2011 | HP LaserJet P2015dn Printer

    1 Answer

    Printer Problem-Not printing at all.


    Hello,

    Half circle = ready to print (when light is on )

    ! mark in a triangle = Attention light : Indicates printer media input tray is empty, print cartridge door is open, print cartridge is missing, or other errors. See Printer information pages for more information.
    ( light on means that there's an error )
    piled circles = toner indicator (light on means toner ("ink") is low, needs replacement)

    There's a help page for these light indicators, just in case other lights are / come on, see:
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?cc=US&lang=en&objectID=c00230632&prodSeriesId=410622&prodTypeId=18972

    Control Panel light indicators overview:


    588167f.jpg

    Jul 23, 2010 | HP LaserJet 1320 Printer

    Not finding what you are looking for?
    HP LaserJet 1320 Printer Logo

    3,236 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Office Equipment & Supplies Experts

    Clive
    Clive

    Level 3 Expert

    4345 Answers

    Ekse

    Level 3 Expert

    13434 Answers

    Thomas F. Schneider

    Level 3 Expert

    2715 Answers

    Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...