Question about Baumatic 24 in. BFD60SS Free-standing Dishwasher

2 Answers

Baumatic dishwasher We loaded up and switched on as normal but we had all the programme lights flash on and it does not seam to load up with water, We checked the filter inside and found it very blocked, after emptying it it still has the same problem. kind regards: Mark

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Baumatic dishwasher

Baumatic dish washer bdf64ss
will not drain and code 8 shows

Posted on Apr 26, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,003 Answers
Re: Baumatic dishwasher - Baumatic 24 in. BFD60SS Free-standing Dishwasher Dishwashers

RepLace water inlet solenoid

Posted on Jan 24, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

When I start the normal 50 button, the top and middle lights blink three times. Then after few seconds the normal 50 and bottom lights start to blink

Start the wash programme
1. Check that when the dishes and cutlery are loaded in the dishwasher
the spray arms are free to rotate.
2. Open the water tap fully.
3. Shut the door.
4. Press the ON/OFF button. ON/OFF button indicator comes on.
5. Press the button for the programme required (see "Programme Table"). The programme indicator lights up. One or two lights will flash in the multi-display. During this time it is possible to reselect the programme. The selected washing programme begins after approx. 6 seconds. The current wash programme stage will always be shown in the multi-display.
3 If the top light and/or the middle light in the multi-display flash after
the programme has started please read the section "What to do, if...".


Jun 13, 2014 | AEG 24 in. Favorit 40630 Free-Standing...

1 Answer

Kenwood KDW243A - It blew the circuit breaker.

hi it probably the heater element had a similar problem on ours.

Oct 26, 2012 | Kenwood KDW243A Builtin Dishwasher

1 Answer

Kitchenaid KUDS01FL -Dishwasher - "clean" light wont stop flashing; cant start a new load


The clean light usually will blink due to a failure to heat the water properly. This dishwasher looks for a temperature rise of the water during a heating cycle if it fails to see this rise for multiple cycles it may shut down and blink the clean light.
There are a few things to check before resetting the control.
-The unit not being level so both door switches do not make contact
- The sump plugged up so water is not pumping across the heater (see sump clean out below)
- Not enough water filling the dishwasher
- The heat element is not working
To reset the control use this key dance within 5 seconds press: HEATED DRY, NORMAL, HEATED DRY, NORMAL
This will cause you to enter the diagnosis cycle once this is finished or you hit cancel the control should be unlocked and ready to use.

Thank you !

May 20, 2010 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

Kenmore Elite Dishwasher clean light ind flashing and won't start

That means the control sensed that the heater in the d/w did not operate 3 times in a row. so the unit locks out. First remove the kick plate and you may have to pull the unit out from under the cab, but check your heater. use a meter to see if it reads open, if so order a heater assy it will come with a new control replace it to. If your heater checks good press in sequence normal wash , heat dry ,normal wash,heat dry , normal wash , heat dry three times within 6 sec all the lights will come on then hit cancel. What that did is reset the control and clear that fault. Keep in mind that d/w does not heat it's own water your incoming water temp should be 120. the d/w will maintain that temp. when starting your d/w first turn on your hot water till it gets hot then start your d/w this insures your unit fills with hot water and not cold

Jan 09, 2009 | Kenmore 24 in. 15142 Built-in Dishwasher

2 Answers

BAUMATIC BFD47SS dishwasher won't start

Sounds like the water inlet solenoid valve is not opening. Not easy to get at to test, but if water is available at the hose inlet connection as you say there isn't anything else stopping water entering the wash cabinet.

Shouldn't be a lengthy repair - so I'd recommend getting a quote.

Aug 09, 2008 | Baumatic Dishwashers

1 Answer

Dishwasher not filling


Jan 17, 2008 | Zanussi 24 in. DE6544 Built-in Dishwasher

1 Answer

Dishwasher leaked water once due to an outlet block, then won't start

It obviously has leaked water on the connections underneath, Lean the dishwasher back and see if any water comes out the bottom, then leave it standing for about a week to dry out and hopefully it should be ok.

Nov 26, 2007 | Baumatic 24 in. BFD60SS Free-standing...

Not finding what you are looking for?
Baumatic 24 in. BFD60SS Free-standing Dishwasher Logo

Related Topics:

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baumatic Dishwashers Experts

Starnley Johnwells
Starnley Johnwells

Level 3 Expert

1029 Answers


Level 3 Expert

56797 Answers


Level 3 Expert

1172 Answers

Are you a Baumatic Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides