Question about Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

D3 error code

I have a GU2400XTPwhirlpool dish washer that first had the saniclean green light flashing, cleared that with the two buttons, now i get a d3 code on the display and the water no longer sprays or even goes into a full wash cycle. I do hear a low buzz some for a bit then it drains. PlZZZ HELP.
Less than 2 yrs old.

Thank you !

Posted by on

  • 1 more comment 
  • jaeg Jan 24, 2008

    No luck, i tried the heated dry-normal-heated dry, and it cycled all lights and started a wash cycle, water filled and the low buzz sounds started up for a while then the drain cycle started.

    maybe the D3 code means the motor/pump is bad since it no longer sprays water.

  • jaeg Jan 24, 2008

    Hi, the D3 did clear up but comes back if i try to run a cycle again then clears it self. I did find a broken glass but was able to recover the few broken pieces and i clean out the lower filter too.

    And yes this did happen from one day to the next. The first problem was the green clean light flashing but was able to clear it out with the buttons heated dry/hi temp. I will check the motor and let you know. Thanks for all the help !

  • tamby Oct 20, 2011

    It is a quiet partner iii sorry

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers

Try running it in service diagnostic and let it finish will check its self and clear error codes in less than 6 seconds push heated dry-normal-heated dry-normal and advise me

Posted on Jan 24, 2008

  • robert samples Jan 24, 2008

    according to the tech sheet d3 is the software code for a tall tub dishwasher but the cycle tell me what i want to know is the d3 code still there or did it clear we aren't done yet pull the bottom plate off and on the motor is a start capacitor silver looking cylinder with two wires on it make sure one of those wires Inst loose let me know did this happen all of a sudden and did you find any broken or chipped dishes or galss in the unit

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My zanussi zwg 6141p washing machine is calling water at start of cycle but is not going into drawer to swill out detergent , is also stopping half way with the green light on the start button flashin


Some appliances malfunction can be displayed in hexadecimal or in binary code.
So your device is defective and shows you what's wrong. You have to count how many times flashes red light and how many times flashes green light. Red light shows the first error number and green light the second error number.
For example: you forgot to close the door and you started washing machine. After some time (timeout) will generate an alarm. Four times will flash red light and once the green light which means error code " E41 " or "Open door"
" E20 " means "No drain water"
" E10 " means "No fill up water"


Dado

Sep 08, 2014 | Zanussi Washing Machines

1 Answer

Lock light stays on my whirlpool quiet partner II


If pushing and holding the lock button till the light goes out doesn't work, you likely have a problem on the circuit board.

May 24, 2014 | Dishwashers

1 Answer

Machine stopped mid cycle and green light flashing under green start button


Many modern washing machines display error codes if they detect a fault, but not all washing machines display a readable error code, some indicate an error by flashing, or lighting some of the lights.

Hotpoint, Indesit, Zanussi error codes

Hotpoint, Indesit washing machines and Zanussi washing machines are some common appliances that display coded error codes. On their more expensive models, they display readable error codes but basic models (without digital displays) use flashing lights to convey the error fault code.

If your washing machine malfunctions and you can see some of the lights flashing, or one or more option lights have lit up, then make a note of which lights are flashing and which option lights are lit. NOTE: the error code list engineers have only shows the option lights by number and not by name. Therefore you need to report the lights as LED 1 and 3, or 2 and 4 etc. and NOT "delay timer" and "extra rinse". Count the lights from the left (or from the top if in a column) and report as "led 1 and 3" etc.

No Option lights?

With basic washing machines that have no option indicator lights, count the number of flashes. For example, the door locked indicator may flash 7 times, pause, and flash another 7 times in a constant cycle which would indicate error code 7.

This information is vital, and needs mentioning when reporting a fault.

Jan 18, 2011 | Zanussi FJS1225W Front Load Washer

1 Answer

Bosch dish washer not washing


are any lights blinking is there an error code on the disp whats the model #

Jul 01, 2009 | Dishwashers

1 Answer

Xerox XC 1045 has a flashing H 4 error.




elem_1_spacer.gif Performing a Fault Reset 14 will reset your copier and will help to clear error codes.
  1. Turn the power off.
  2. Locate the Clear Button, which is grey in color, in the upper right corner above the green Start Button.
  3. Locate the Auto Button the lower left corner of the Control Panel.
  4. Turn the power back on.
  5. Press the buttons in the following sequence, releasing each button after each time you press it: [Clear], [Auto], [Clear], [Auto]. Every light on the Control Panel should go out, and the error code should clear.
  6. If the error code has not cleared, wait a few seconds then repeat Steps 1 through 5.
  7. Program the copier as if you were going to make 14 copies.
  8. Press the green [Start] button to store the reset code. The copier will return to the ready position.
  9. Run a test copy.

Jul 01, 2009 | Xerox Office Equipment & Supplies

1 Answer

Xerox XC1020 Flashes code H 4


This should resolve your issue. If not it would most likely need a heat rod. But there ia probably a 99 percent chance this will cure it. Let me know please.

Performing a Fault Reset 14 will reset your copier and will help to clear error codes.
  1. Turn the power off.
  2. Locate the Clear Button, which is grey in color, in the upper right corner above the green Start Button.
  3. Locate the Auto Button the lower left corner of the Control Panel.
  4. Turn the power back on.
  5. Press the buttons in the following sequence, releasing each button after each time you press it: [Clear], [Auto], [Clear], [Auto]. Every light on the Control Panel should go out, and the error code should clear.
  6. If the error code has not cleared, wait a few seconds then repeat Steps 1 through 5.
  7. Program the copier as if you were going to make 14 copies.
  8. Press the green [Start] button to store the reset code. The copier will return to the ready position.
  9. Run a test copy.

Feb 16, 2009 | Xerox Office Equipment & Supplies

1 Answer

FLASHING LIGHT AT END OF PROGRAM


what does the green light say hit cancel it may be a reminder that the dishes are clean if you give me the complete model i can look up the tech sheet a stuck button can also flash rapidly cancel will clear it

Jan 09, 2008 | Whirlpool 24 in. ADG6340 Built-in...

1 Answer

Flashing error code


Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.
  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.
elem_1_spacer.gif

Dec 20, 2007 | Toshiba e-Studio120 Copier

3 Answers

Flashing 4-H error message


try this reset procedure. Most likely this will work.

Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.
  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.

Nov 29, 2007 | Sharp AL 1631 Copier

2 Answers

Indesit D167. When cycle selected no water pumping or filling but 1 & 2 green indicators on.


Tilt your dishwasher forwards. Be aware that water will come out ouf the bottom. Once this is clear your washer should be Ok.
Good Luck

Sep 23, 2007 | Indesit 24 in. DI67 Free-standing...

Not finding what you are looking for?
Whirlpool GU2400XTP Built-in Dishwasher Logo

801 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Mike

Level 3 Expert

4356 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...