My new epson stylus NX110 wont download into my computer it said it needs a driver

You can download the Epson printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :-http://www.epson.com/cgi-bin/Store/jsp/index.do?BV_UseBVCookie=yes

Follow the link below:
http://files.support.epson.com/htmldocs/nx110_/nx110_ug/wwhelp/wwhimpl/js/html/wwhelp.htm

Click "replace ink cartriges" on the left of the page
and then select "Remove and install Cartriges"

http://files.support.epson.com/htmldocs/nx110_/nx110_ug/wwhelp/wwhimpl/js/html/wwhelp.htm

The drivers for supported OS versions are available from Epson, Go to http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?cookies=no&oid=128284&infoType=Downloads&platform=Windows&com.broadvision.session.new=Yes . If you have a Mac, use the drop down menu to select that and press the Go button. Then select the downloads appropriate for your computer.

I hope this helps.

Cindy Wells

http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=128284&prodoid=63084353&BV_SessionID=@@@@2031028487.1288229096@@@@&BV_EngineID=ccfjadellejemldcfngcfkmdhjidfmh.0&cookies=no&infoType=Downloads&platform=Windows&x=18&y=8

Hello,

The Epson NX110 is in fact an ink jet printer.

http://files.support.epson.com/pdf/nx110_/nx110_sl.pdf

Thanks,

Pat

You can get the driver from this site:

http://esupport.epson-europe.com/ProductHome.aspx?lng=en-GB&data=wsMoc1iChVGs8xyY6tppQqeurEYBTh8ntD7N++kOb2oU003D&tc=6

*** I'll be more than happy to help you on that.
there is a great possibility that the nozzles of your printer are clogged by dried inks.maybe cause by the previous inks that you just replaced. we can check that by printing a nozzle check pattern.

1. Load a few sheets of plain paper in the sheet feeder. 2. Turn off the Epson Stylus NX110 Series. 3. Hold down the Stop button as you press the On button to turn the Epson Stylus NX110 Series back on. When the On light begins to flash, release the Stop button. 4. Check the nozzle check pattern that prints to see if there are gaps in the lines. 5. If there are no gaps, the print head is clean and you can continue printing. If there are gaps or the pattern is faint, clean the print head. Using the Control Panel 1. Load a few sheets of plain paper in the sheet feeder. 2. Make sure the Epson Stylus NX110 Series is on and the ink light is off. 3. Hold down the Stop button for three seconds to start the cleaning cycle, which lasts around one minute. The On light flashes throughout the cleaning cycle and stays on green when the cycle is finished. Caution:
Never turn off the Epson Stylus NX110 Series during a cleaning cycle or you may damage it. 4. Run a nozzle check to confirm that the print head is clean. You may need to clean the print head up to 4 times. You can also turn off the Epson Stylus NX110 Series and wait at least 6 hours. Then try printing again.

Here is what I found on Epson Web site. Click on link below. IF YOU FIND THIS HELPFUL PLS RATE ME. THANKS AND GOOD LUCK......

http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&infoType=Doc&oid=128285&prodoid=63083739&category=Products

If you need to change a cartridge before it or any other cartridges are low or expended, run the Ink Cartridge Replacement utility.

You cannot print or copy when an ink cartridge is expended even if the other cartridges are not expended. Replace any expended cartridges before printing or copying.

Leave your old cartridges in the Epson Stylus NX110 Series until you are ready to replace them to prevent the print head nozzles from drying out.
When an installed ink cartridge is more than six months old, you may need to replace it if your printouts do not look their best, even after cleaning and aligning the print head.
Follow the instructions in these sections to check and replace your ink cartridges:
Replace Cartridges Using a Printer Software Utility
For best printing results, use up a cartridge within six months of opening the package. If you need to replace a cartridge when the ink light is flashing or off (before the cartridge is expended), you can run the Ink Cartridge Replacement utility.

1. Windows: Right-click the printer icon in the bottom right corner of your screen (the taskbar) and select Printer Settings. Click the Maintenance tab.
Macintosh: Open the Applications folder, open EPSON Printer Utility3, select your printer (if necessary), and click OK.

You see one of these screen SEE ATTACHMENT BELOW

2. Click the Ink Cartridge Replacement utility icon and follow the on-screen instructions to replace your ink cartridges as necessary