Question about Zanussi FJS1225W Front Load Washer

1 Answer

Zanussi jetsytem fjs1225w

can you help the softner wont go into the washing machine it just stays in the drawer, any ideas how to fix this

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 54 Answers
Re: zanussi jetsytem fjs1225w

Clean the draw out remove the top where the softner goes and clean under there.

Posted on Feb 14, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Fabric conditioner compartment will not empty when in cycle

FJS1225W Front Load Washer This video will show you how to keep your soap draw clear and how to service the parts
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.

May 17, 2010 | Zanussi FJS1225W Front Load Washer

1 Answer

My fabric softner wont go away from drawer

remove the soapbox drawer and clean it thoroughly, you will find a lot of gunge is blocking the small hole were the fabrick conditioner section is.

Feb 02, 2010 | Zanussi FJS1225W Front Load Washer

1 Answer

Will not take softner?

clean the dispenser drawer, then using thin pipe cleaner clean the two outlets that fall over the softner drawer, its easier if water is flowing from them, to do this switch on the servvice cycle (no clothes in the machine) as u swtich it on, hold the start pause and skip button down and then press the fabric button repeatedly until the water comes through the outlets over the softener compartment.

to exit service cycle u must swtich the machine on and off twice

Dec 28, 2009 | Zanussi FJS1225W Front Load Washer

1 Answer

Jetstream 1200 wont take away fabric softner

strip and clean out the soap tray then remove the tray and clean the fill water holes above it with a stiff washing up brush.

Mar 16, 2009 | Zanussi ZWF1430W Front Load Washer

1 Answer

Softner wont go into the washing machine

removing the front plate won't help you, take the draw out. Get a long bag tie or inner core of any mains twin and earth cable and push it into the holes in the top of the dispensor, move it about in/out etc, changing the holes as required, this normally works, if it doesn't the dispensor lid is available as a seperate part and is quite easy to change.

Jul 06, 2008 | Zanussi FJS1225W Front Load Washer

1 Answer

Machine wont take conditioner

hi there remove soap drawer and softner compartment lid clean throghly both hole and tube inside and out failing that clean soap box lid inbside with bottle brush at worst you may need to replace the soap box lid assy

hope this is of some help

Jan 11, 2008 | Zanussi FJS1225W Front Load Washer

1 Answer

Zanussi err problem

Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped.

Dec 10, 2007 | Zanussi FJS1225W Front Load Washer

1 Answer

Softner remaining

Try diluting the softener, some softener are too thick. But first clean out the softenre tray, by pulling it out, or with a tooth brush. Do look into your user manual. Does water enter the soft tray, check this too.

Sep 08, 2007 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Zanussi FJS1225W Front Load Washer Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides