Question about Dryers

1 Answer



Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 57 Answers

They normally have a thermal cut out on the rear, behind a small cover or rubber area. Reset this by pushing it in. You have probably let it get too hot at some point by not keeping the filter cleaned often enough, or the outlet hose getting blocked. If there is not a reset, or it doesn't resolve the problem, it may be a fault with the hetaer element. These are not normally difficult to replace, just normally difficult to get to!

Posted on Jan 22, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Dryer runs and only blows cold air

The problem is the ignitor...

Check out this tip that I wrote about that problem...


Apr 07, 2010 | Kenmore 72822Gas Dryer

1 Answer

LGR7646EQ0 Dryer runs but no heat (new ignitor)

check all the thermal fuses with an ohm meter if one of then is not showing any continuity the replace it this should help good luck

Jan 23, 2010 | Whirlpool LGR7646E Dryer

1 Answer

Gas dryer wont heat up, blows only cold air.what would cause this

Could be a bad hi limit thermostat. Could be a bad glowbar ignitor. Check the glowbar ignitor at the gas valve, is it glowing bright orange/red? If not. Replace the ignitor.

Jul 22, 2009 | Whirlpool Dryers

1 Answer

Dryer heats, tumbles clothes, blows air out exhause vent, but wont dry clothes

what type is this electric or gas? have you removed the exsaust from the wall and ran a load like this? if you have heat and this is an electric dryer it sounds like you have a blockage in your house. if the dryer runs fine without the exsaust attached then that is your problem. let me know

Jun 02, 2009 | Kenmore Dryers

1 Answer

The dryer won't heat

The heating element may be bad.

Apr 06, 2009 | Whirlpool LEQ8000JQ Electric Dryer

2 Answers

The dryer only blow out cold air.

When I turn the dryer on, only cold air blows out. There's no heat. I cleaned out the vents? What do you think is my problem> Thank you very much. K

Oct 18, 2008 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

Blows fuse for heat after about 30 minutes

yes , occassionally though it will run for full cycle ....but not very often

Sep 06, 2008 | Kenmore 73952 Gas Dryer

1 Answer

Maytag dryer wont heat up

Could be grounded heater element.

Mar 23, 2008 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts


Level 3 Expert

77932 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Brad Brown

Level 3 Expert

16806 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides