Just had my oil changed and now one preset station has the message " inov 712 ". What is the issue here? problem is on a 2001 pontiac grand am, 3.4

You don't set these buttons. The traffic button scans Radio Data Service (RDS) information from radio stations near you for Traffic information. The Info button changes what RDS information is displayed for the current station.
The numbered preset buttons are the only buttons on the radio you can program. Too program a preset, tune the station desired and hold the numbered preset button down until you hear a beep.

How do you reset oil change light on 2001 Pontiac Gran Prix SE hope this helps

When a vehicle is in 3 feet of water, the electrical
is usually damaged to the point that the vehicle
is scrapped
The vehicle is 12 years old or more,so even without
the water in there, it has some wear & you can use google
to check for bulletins of known engine issues,but I don't
think your going to fix that, even without the water issues.
The motor would have to come apart to find the issue & you
may rebuild it & never know

A very common issue with these engines are fuel injectors going out on the 3.4 or 3.1L. Another issue are vacuum leaks around the plenum gasket. You can spray throttle body cleaner around the plenum gasket and listen for rpm changes.If the rpms change while doing this the plenum gasket may have a leak.

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. and wait for the light to flash. Check your manual it maybe slightly different. Real easy fix.

if your vehicle does not have the optional Drive Imformation( DIC) do the followig. 1.with the ignition key ON, but the egine OFF , fully push and release the accelerator pedal 3 times within five seconds. - the Change Engine Oil message should be off - If the Change Engine Oil message comes back on, the engine oil life monitor has not reset, Repeat the procedure. If your vehiclehas the optional ( DIC ), do the following: 1 turn the engine ON, with the engine OFF. 2 press the MODE button until the DIC reads OIL LIFE LELT/ HOLD SET TO RESET 3. press and hold the SET button until 100% is displayed. You will hear 3 chrimes and the Change Engine Oil message will go off. if the Change Oil message comes back on, the system has not reset, Repeat the procedure. Hope this can help , Good luck

If you want to repair the oil pan I would also check lower engine mount for leaking oil and cracks in anti sway bar near fitting's. This due to engine mount is oil filled. OEM sway bar is made of tubular steel and they crack easy. Replacement sway bar is solid steel. Here's the kicker. When they pull the lower frame to service oil pan. The engine mount and sway bar are attached to that frame. A honest mechanic should only charge for parts ($35 for mount and $100 for sway bar) and maybe a extra hour. My mechanic did all in 5 hours. FYI gasket is only $35 bucks. Good luck

Pontiac Aztek, Montana 2001-05 w/o (DIC) Driver Information Center; Torrent, Ascender 2006

Turn the ignition to ON, with the engine off. Fully depress and release the accelerator pedal slowly three times within five seconds. Turn the key to OFF If the CHANGE ENGINE OIL’ message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Pontiac Aztek, Montana 2001-06 wI (DIC) Driver Information Center

urn the ignition to ON, with the engine off. Press the MODE button until the DIC reads ‘OIL LIFE LEFT/HOLD SET TO RESET Press and hold the SET button until 100% is displayed. You will hear three chimes and the “CHANGE ENGINE OIL” message will go off. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Good luck

Try just holding the button of choice down. In my Audi, when I had a factory head unit, to set for example, preset 2, I'd just tune to the station I wanted to program, and then hold down the number 2 preset button until the display stopped blinking. It was then preset.

tune to a station manually then press on the preset number for 3 seconds and the frequency will be stored..do it again to the rest of the preset numbers...

tnx 4 using fixya,

drcool