Missing cord that connects unit to power outlet

Hello Sarah,

Check the power cord connections at the dryer terminal itself. You'll need to unplug the dryer, then remove the cover where the cord enters the dryer. It is very common for these to burn and break due to loose connections.

Did you also try a hard reset?
Not sure if this will help, but found this video
How to fix an Electrolux washer that has no power or frozen screen

• It may be a little confusing. You actually plug the USB computer cord into the back of your GPS (see diagram) and then plug the AC power cord into the end of the USB cord (that would normally go into a USB port on your computer.) In effect two wires connected together. Then plug the AC adapter into your outlet.

• Hope this helps.

Hi jesseley,
Do it has a led light when you plug the unit to the outlet, make sure that the outlet is live, what happen when you pressed the power on switch in the front panel?
Jdvillanueva

Are you sure there is power on the outlet? If yes then probably the power cord is at fault. You should have a handy tester at hand to go further. You could buy a cheap one at any hardware or electronic shop. Now for the power cord. First remove the back cover of your unit. Then set your multimeter to voltmeter range... at the highest range. Plug your oven to the power outlet. Trace the line of the power cord inside the oven. Look for the connections and markings for Line1 and Line2. Now point your test prod to these connections. You should read a voltage similar to your power outlet. If not then replace the power cord. If its OK then remove the power cord to the power outlet. Set the multimeter to the Ohmmeter range. Check the coil if it is OK. You should read a reading of less than a hundred ohms or more. Be sure to remove any connections to the coil before doing this test. If everything goes well according to the test procedure then the culprit must be the power switch or the connection going to it or to the coil.

Check your power supply cables Your power supply cables may not be fully secured. Let's unplug and reconnect your power supply

1. Disconnect the power cord from the back of your console. Unplug the power cord from the wall outlet and the power supply unit.
   Reconnect the power cord to the console. Then plug the power cord back into the wall outlet and the power supply unit
2. Make sure that all three connections are firmly secured.
3. Turn your console back on.
   
   

Check the light on the power supply. If this solution worked, your power supply light will be green

Let's unplug and reconnect your power supply

1. Disconnect the power cord from the back of your console. Unplug the power cord from the wall outlet and the power supply unit.
   Reconnect the power cord to the console. Then plug the power cord back into the wall outlet and the power supply unit.
2. Make sure that all three connections are firmly secured.
3. Turn your console back on.
   Check the light on the power supply. If this solution worked, your power supply light will be green and the power button will look like this:

Your power supply cables may not be fully secured. Let's unplug and reconnect your power supply

1. Disconnect the power cord from the back of your console. Unplug the power cord from the wall outlet and the power supply unit.
2. Reconnect the power cord to the console. Then plug the power cord back into the wall outlet and the power supply unit
3. Make sure that all three connections are firmly secured.
4. Turn your console back on.
5. Check the light on the power supply. If this solution worked, your power supply light will be green....

Hi,

Try the following to bring the touch screen backto life.

Step 1:

Do a power flee by unplugging the power cord from the rear of the printer and holding down the power button for 30 seconds.

If the above doesn't resolve the concern, then try the step 2.

Step 2:

Perform a Full Reset of the HP Photosmart ,
-Press the On button to turn off the unit.
-Disconnect the power cord from the back of the unit.
-Disconnect the power cord from the AC outlet.
-Connect the power cord to the back of the unit.
-Connect the power cord to the AC outlet.
-Press the On button to turn on the unit.

If the touch screen has not gone bad,the above troubleshooting steps should resolve the issue.

Thanks and regards,
Techbuddy247

If power cord was jerked out of the outlet or set, make sure it wasn't damaged. If it was unplugged violently, the circuit board inside the set could be damaged. Also make sure the outlet that it is plugged into is not damaged or a switched outlet.

Hi,

I have a questions for you, is the unit connected to a surge protector, or to a wall outlet.

If its connected to a wall outlet then the power supply will not be directly to the unit, as these units come with a built in surge protector in them.

You can try connecting the unit to a wall outlet, and if no go then try this step.

Disconnected the power cord from the unit as well as from the wall outlet.

Press and hold the ON button on the unit for 30 sec and then plug in the power cable to the wall outlet and then to the unit.

Remember to connect the cable to the wall outlet first and then connect it to the back of the unit.

This should probably fix the problem,
Please let me know if there is any other issues.