Question about IBM 6400 Model i10 Matrix Printer

1 Answer

P17 Security Violation

Please, need help.
thank you.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers
Re: P17 Security Violation


This is not a good sign. Have you recently replaced the controller board ? Or upgraded the microcode. This error refers to the Security Pal chip on the controller board. Itt would be worthwhile reseating it , if you are compitent to do so. Otherwise you may be lokking at calling an IBM engineer to solve the problem.

Where are you located ?


Posted on Mar 06, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

After replacing a logic board on tallygenicom,it desplays the error "sucurity violation" how do i resolve that problem

Security lock was installed in the previous logic board remove the security lock and install it in the new logic board.

Feb 28, 2013 | TallyGenicom Printers & Copiers

1 Answer

RZ220 code P-17-20 any info would be helpful

P17-020 means that you have to enter an user code on the additional accessory that's been installed on the printer. Usually it is a copy controller called "HECON". If that is not the case, then the counters have been disconnected.

Mar 06, 2012 | Riso RZ220 Duplicator

1 Answer

Reset samsung ml 1860

The ML-1860 yields 1500 A4 pages at 5% toner coverage.
To reset the cart you have to purchase the toner chip or reprogram(if you have experience). Also you may search the Internet for firmware fix which is violation of warranty.

Dec 13, 2011 | Samsung Printers & Copiers

1 Answer

Do I need to use hp products only?

No but if you use third party (non-HP) products you will invalidate the warranty and potentially you may damage the printer. Having said that, many users can and do purchase cheaper non-HP consumables and claim that they produce output of comparable quality. In the end it's down to you to weigh up the risk offset against the potential cost savings. HP (or any other printer manufacturer) obviously want you to purchase their own branded consumables, so they're always going issue dire warnings about warranty violation and inferior quality issues from using third party products. One other thing to bear in mind, it tends to be just as cheap/expensive to replace a printer as it does to repair it!

Would you kindly rate my answer please if this has helped resolve the problem - thanks :)

Oct 20, 2010 | HP Photosmart C4280 Aio Printer

7 Answers

EXITING TALLY!! Internal Error. Contact Tally

My tally 5.4 not open when to try open tally when see exiting tally! file not found. Please give the solution immediately 

Apr 27, 2010 | Tally T2245 Matrix Printer

1 Answer

Trying to scan I get the error message ''A Sharing violation occur

Create a new windows user account .Try to scan the document in the new admin user account.

Aug 17, 2009 | Lexmark X5495 Printer

2 Answers

Sub : TALLY 7.2 error

exiting tally! \r\ninternal error
software exception c0000005
(memory access violation)

Apr 20, 2009 | Tally T2250 Matrix Printer

1 Answer

Konica 3135 p17 error, wont go away

Check the rear side of the machine in the opening. You should see a small tab on the rear side of the door. This tab is supposed to go through a small slot in the cover that would then contact the door sensor/switch to tell the machine that the door is closed.
If you located the little slot, you can try rolling up a piece of paper putting it in the slot and see if you can trick the machine to think the door is closed. If you can do this then you know that the sensor/switch is working and then you would have to concentrate on the door tab that is supposed to go through the sensor. Unfortunately, if you get the machine to think the door is closed with the paper trick, you still wont be able to make a copy cause the door needs to be closed in order for the rollers to feed the paper upwards. But at least you would be able to narrow it down.
If you have any other questions, feel free to ask. I even still have some contacts for parts if needed.
Please remember to leave a feedback if my suggestion helped.
Have a good day.

Feb 11, 2008 | Printers & Copiers

Not finding what you are looking for?
IBM 6400 Model i10 Matrix Printer Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top IBM Printers & Copiers Experts


Level 1 Expert

34 Answers


Level 3 Expert

1113 Answers

Brad Brown

Level 3 Expert

13355 Answers

Are you an IBM Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides