Question about Brother Sewing Machines

1 Answer

The part in which needle is fixed keeps coming out so how to fix that?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

I dont understand what you mean. does the needle come out of the shaft, if so maybe the screw holding it in place is not tight enough or may need to be replaced

Posted on Dec 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The thread in the needle in My Brother JX2517 keeps coming out from the eye every time I try to sew. It does not break bot comes out of the needle. What is the cause and how do I fix it?

Pull more thread tail through the needle eye and hold the thread tail in your left hand when you begin the first couple of stitches. It also helps to have the needle at its highest point when beginning the first stitch.

Jan 15, 2018 | Brother Sewing Machines

1 Answer

The thread on my Elnita sewing machine keeps coming out of the needle and won't sew. How can I fix this?

Make sure to pull at least 4-5 inches of thread through the needle eye before beginning to stitch. It will help to also hold the thread tails in your left hand while slowly taking the first few stitches. Another help is to raise the needle to its highest when starting to stitch.

Nov 17, 2017 | Sewing Machines

1 Answer

My lower needle (the lowest one that runs right to left) keeps coming un-screwed.

The screw that holds the needle in place could be stripped. There could be some DIY fix-it methods, ie nail polish to coat the screw threads. But short of that, you can probably have the part replaced or perhaps order the part and replace it yourself.


Jan 26, 2016 | Brother 1034D Serger Sewing Machine

1 Answer

Needle scrapping

Servicing the Timing is NOT a home fix

Feb 17, 2014 | Singer Confidence 7463 Computerized Sewing...

1 Answer

#1 thread keeps coming out on the 3/4 thread kenmore serger. How do I fix this problem?

try rethreading the needle & keeping thread tails of at least 4 to 6 inches that you can keep pulled behind the needles

May 03, 2012 | Kenmore Sewing Machines

2 Answers

My needle does not stay threaded on my Brother Lx 3125 (the top thread) it keeps coming out of the needle while stitching. How can I fix this?

keep a thread tail of 3-5 inches & when you sew make sure the thread is pulled behind the needle each time you sew, even if you have to hold the thread tail with your fingers

Nov 24, 2010 | Brother LX3125 Sewing Machine

1 Answer

Having trouble threading the needle, thread keeps

You might have either a tension problem or a bent needle. Try replacing the needle and then re-thread the whole thing and see if that helps. The majority of the time when I am having thread-breaking issues, once I replace and rethread, it is fixed. Hope this helps.

Feb 22, 2010 | Elna Sewing Machines

2 Answers

Needle keeps falling out of Pfaff Creativ 2170

change ur needle bar and also check needle size before insert in it.

Sep 14, 2008 | PfaFF Sewing Machines

1 Answer

Kenmore 385 timing answers

the needle/ hook timing is achieved when the needle is in the lowest position and just starting to come up and the shuttle hook is at or close to the needle eye
there is a clamp on the vertical shaft the the needle is attached to so loosing of the clamp and moving the needle arm up or down to achieve that desired position is required
retension the clamp
if you machine is belt driven between the needle operation and the shuttle operation and it keeps altering timing it is possible that that belt needs replacing as the tooth sections of the belt may be worn off and jumping the teeth of the drive sprockets
it may be advisable to find another repair and get quotes first now that you have some idea of how it works

Jun 07, 2017 | Sewing Machines

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1134 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Irene Tulloch

Level 2 Expert

484 Answers

Are you a Brother Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides