Question about Sony SPP N1000 Cordless Phone

1 Answer

Spp n1000 Need instructions to set 10 number auto dial.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

1.Press PGM. The Talk/Batt Low lamp flashes.
2. Press SPEED DIAL.
3. Press one of the dialing keys (0-9) to store phone number. You will hear confirmation beep.
4. Enter the phone number you want to store (up to 20 digits)
5. Press PGM. You will hear a long confirmation beep and number is stored. Tall/Batt Low lamp goes off.
Do not allow more than 20 between each step of the procedure. If you enter a wrong number, press PGM and start over.

Posted on Apr 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic phone model kx-ts108w how to change emergency to a new number on this phone


Page 20 in the manual

ftp://ftp.panasonic.com/telephone/om/kx-ts108_en_om.pdf

PDF]Operating Instructions - FTP Directory Listing - Panasonic

ftp://ftp.panasonic.com/telephone/om/kx-ts108_en_om.pdfIntegrated Telephone System. Model No. KX-TS108W. Pulse-or-tone dialing capability. Operating Instructions. Preparation. Basic Operation. Advanced Operation. Useful Information. PLEASE READ BEFORE USE AND SAVE. Panasonic World Wide Web address: http://www.panasonic.com for customers in the USA or ...
20
Storing Phone Numbers
You can store up to 20 phone numbers in the one-touch auto dial buttons
(10 numbers in UPPER memory locations, 10 numbers in LOWER
memory locations).
Make sure that a call is not put on hold.

To store in an UPPER memory location
It is recommended that you program an emergency number in the
EMERGENCY button.
1
Press
(PROGRAM)
.
2
Enter a phone number, up to 22 digits.
?
If you enter a wrong number, press
(PROGRAM)
and start again from step 1.
3
Press one of the one-touch auto dial
buttons.
?
A long beep sounds.
?
The unit will return to the standby mode.
?
If 3 beeps sound, the number entered in step 2 may be over 22 digits.
Press
(PROGRAM)
to return to the standby mode, and start again from
step 1.
?
If a pause is required for dialing, press
(PAUSE)
where needed. Pressing
(PAUSE)
counts as one digit (p. 24).
?
When using the Dial Lock (p. 27) or Call Restriction feature

May 01, 2018 | Panasonic Lands Phones

2 Answers

I need the Roku N1000 set up instructions.


This manual is VERY similiar to the original N1000. I have the N1000 and just upgraded to the XPS or 2100x. Again, these units are very similiar.

http://www.wigix.com/index.php/skuaccessories/downloadManual/4004116/20550/0/Roku-Netflix-Digital-Video-Player---Manual.pdf

Sep 05, 2010 | Televison & Video

1 Answer

Base station on SPP-N1000 rings in steady tone when call comes in and continues ringing after handset is answered. Handset rings normally. How do I fix?


Ok IF you can answer the Call and it still continues to ring, then this is a real wired problem, Usually, the "Ring" cycle, is used to "Trigger" a "Alerting" circuit that then makes a sound, when the call is answered, this "Resets" this circuit. Now IF it does continues, to ring AFTER the handset has answered the call as normal, then obviously, either the handset, is sending the correct signal back to the base, and the base is putting the call through, BUT the Ring Circuit, isn't being Reset. The fault, then must be with the base. You will have to get it looked at. As an aside, when does it stop, I mean it must, or that would have been your query too? No? So I assume, that it does eventually, stop, I expect it would, as usually, you would design in a "Watch Dog" circuit, that would, time out, if the circuit, didn't reset itself after a pre-defined period. So, Thats the Diagnosis, you will have to repair or replace. As usual though, remove from power, reset as if new, if still faulty. You know what to do.

Apr 16, 2010 | Sony SPP N1000 Cordless Phone

1 Answer

How to program speed dial on sony spp-a946 cordless phone


  1. Press 'PGM'- "program" button.
  2. Press "speed dial" button.
  3. Select "station # " i.e. any button from 1-9 for speed dialing.
  4. (make sure to make a note of this selected # against the corresponding tel # and /or the person's name)
  5. Dial the complete (incl. 1 for USA or country code for other country tel. #s) telephone number to be stored for the selected speed dialing station #.
  6. Press "PGM" button again to complete the storing of the tel #.
  7. Test, after dial tone, by just pressing the selected station #

Mar 13, 2009 | Sony SPP A946 Cordless Phone

2 Answers

Speed dial access


It's easier if you have access to the database to put in names with the numbers, but in the simplest sense, you can take a piece of paper, write down locations, and start entering numbers.

PROG

They are added in sytsem speed dial from the first extension or one designated as the manager's phone. PROG **1234 gets you into programming and 001 is the system speed dial area. With a combination of NEXT's and ENTER, you can be looking at SD 000 (ie PROG **1234 NEXT NEXT ENTER NEXT) and you're ready to enter a speed dial in bin 000. The complete number starts with an access code (9) plus the number as you would dial it. For example 918005551212 ENTER puts that number in bin 000. NEXT will step to 001.

USE

Press INTERCOM or select a line and press AUTODIAL and dial the 3 digit code. If your installer was lazy, you will have a problem as "9" selects the highest line in a trunk group, one that you might not have. In that case, he'll either have to program the system properly, or you will always have to pre-select a line to use speed dial.

Notice that this is just hte instructions for SYSTEM speed dial. I guessed that it was what you're looking for. Personal speed dial is a different set of instructions and it could be either under a button or in your 10 or 100 number personal directory (so that's where the 2 digit SD's went :-))

Anyway, if you need those instructions and can't find them in the user manual, please post back.

Carl




Nov 21, 2008 | Panasonic KX-T7630 Corded Phone

1 Answer

Sony SPP-M920


The numbers have rubber keys and on the back is a dry conductive carbon to short the keys.

To fix, you can try to clean it or glue a small piece of aluminum foil on bottom of the rubber pad. They sell a carbon coating in a small bottle too.

AL

Jan 01, 2008 | Sony SPP M920 Cordless Phone

1 Answer

Sony spp-900 cordless phone


Go to the sony website and down load the user manual at this link. http://esupport.sony.com/US/perl/model-documents.pl?mdl=SPP900®ion_id=1

Jun 28, 2007 | Sony SPP 900 Cordless Phone (SPP-900)

Not finding what you are looking for?
Sony SPP N1000 Cordless Phone Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Lands Phones Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a Sony Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...