Question about Ovens

1 Answer

Broken oven display showed fo3 so turned off and back on at mains then there was no power to the oven.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers
Re: broken oven

See if your clock has a power on button or a reset do you know who made it ge, whirlpool,etc

Posted on Jan 21, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

The display flashes F C then starts beeping. I turned off the breaker for 5 minutes and put back on but it started again.

Communication error detected by display board(main board), Lower oven relay board not powered up, check all power connections to the oven relay boards. Check all connections from the main board to the relay boards.

Aug 22, 2015 | Thermador SC272T Electric Double Oven

1 Answer

Our Whirlpool OBI C10 Oven has stopped and is displaying FO3 on the panel. I switched the supply off and on to try and reset, but to no effect. What is the cause?


Thanks for using FixYa. Error F03 in your range/oven means oven temperature sensor circuit failure. To resolve this issue you’ll have to check the oven temp. sensor circuit if the reading is more then 1100ohms then it should be replaced however, if the rating is fine then it is the Electronic Range Control (ERC) that has gone bad & should be replaced. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Aug 24, 2010 | Whirlpool Ovens

2 Answers

Digital display is not working

you need to check the main power and see if the power is orrect if so replace the electronic control better known as the clock timer

Jul 24, 2010 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Oven does not start. checked owner's manual. Still does not start. The control panel works and does not display a problem code. The broiler and top burners work. Ideas?


You must check the main power wires where they enter the range at the T-block, sometimes they can burn off. Also check house fuses (or breaker) that supplies power to the range. Checking with a volt meter, you should get 240 volts between the black and red main power wires. The range receptacle and power cord can also burn and fail. Also check the fuse/circuit breaker and check to see if power is getting to the range/oven. If anything does not turn on then check for a blown fuse or tripped circuit breaker. Often the main wiring connection from the house, at the range/oven, gets burned and so breaks the connection. Then you may have to replace the power cord to the range/oven, and the terminal block that the wire is attached to. There may be a broken or burned wire at the back of the range/oven. If you repair any of the wires, use only proper appliance-grade wire and wire connectors.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Oct 13, 2009 | Magic Chef Ovens

3 Answers

Kitchenaid Superba microwave oven combo close door error

turn off the main power outlet it will work.

Feb 09, 2009 | Ovens

1 Answer

Wont' heat in broil or bake

check incoming electric first, pull it out and gain access to main wire terminal, With multimeter set to at least 250v AC , check your power across the wiring as such. black to white (110v), red to white(110v) and then black to red 230v. if that ok ok turn, then start ckin elements for continuty also there might be a thermostat( usually an 1 in. round component with 2 wires located right inbetween the elements that has gone bad, will show no continuity. ck that before electronic control the fact that its clickin sounds like the relays are workin properly

Feb 23, 2008 | Ovens

1 Answer

My oven is beeping!

Try turning it off at the mains, then whilst turning it on, press and hold the cancel button.
Check the fuse and any other electrics on the same ring; eg. Washing Machine - this can indicate that the circuit breaker has tripped, replace any fuses and check integrity of electric on that circut, then flick it back on.

Jan 26, 2008 | Frigidaire GLEB27S7A Electric Single Oven

1 Answer

Whirlpool electric oven

hi switch main power off at wall. hold middle clock button in and switch power back on at the wall. Display should show --:-- and oven should work.

Nov 30, 2007 | Ovens

1 Answer

Display doesn't work, but oven works

First turn the electricity off by locating the breaker to the oven and turn it off. Now wait for an hour or so and turn the breaker back on, if the display turned back on, you need a control board (other manufatures call it a clock, PCB or ECC but it's the main elctronic board with the diaplay built in). If it didn't come back on, turn the power off again and make sure all the wire harness's going to the board are connected good. Turn the power back on and it the display still doesn;t come back on you need to replace the main electronic control board. By the way double check the model number and brand because it might be wrong. Please post back.

Oct 04, 2006 | Whirlpool RBD275PD Electric Double Oven

1 Answer

No display

There is a safety thermostat located in the back side of this oven. When looking at the oven, from the back side, it will be located on the right side. I have a part number of 318003613. Good luck.

May 27, 2006 | Frigidaire FEB30S5DC Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

William Miller
William Miller

Level 3 Expert

8795 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides