Question about Washing Machines

1 Answer

Need to place projector certain point but cannot reduce picture to fit screen canot find manual for model Hitachi PJ-TX200 Projector any tips

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers
Re: Need to place projector certain point but cannot...

Your user manual can be dowloaded here:

Posted on Jan 20, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to change belts on Keystone K108 8mm movie projector.

I strongly suspect a broken belt the covers need to come off.

Jul 20, 2016 | Washing Machines


Miele W946i washer/drier faults-water leaking from back of machine

This tip/guide should be read in conjunction with the excellent tips for the 945i machine given by Bill W. This particular fault may be observed by water leaking from the bottom (vent) hose from the condenser, at the back of the machine, eventually causing the flood/drain fault light to come on. Although the 946i was modified by having a fluff removal cycle that flushed water into the fan outlet, thus removing the fluff/debris build-up that caused the problem in the 945i and so well described above, the condenser fault causing water leakage is common to both machines.

Certain points mentioned in Bill's tip are relevant: draining the drum and pump at the front; then removing the plastic kick-plate in order to extract any tools or bolts that might have fallen during the operation described below. N.B. it is not necessary to remove the front door and seal-plate unless the dispenser assembly, drain pump etc. is to be removed. In particular, wear gloves as the drum will cut at some points on it's circumference at the back. Finally, Corbin type pliers are indeed a must otherwise those brown wire clips that fit on the bottom two condenser hoses are extremely difficult to fit. ( A towel underneath will catch whatever is dropped hopefully or look at floor- level into the bottom tray but mind the float switch assembly.)

I found removing the condenser quite easy and a lever was very useful; reinserting it was also easy by pushing the drum at the same time as reaching down and pushing in the spigot into the rubber drum seal at the same time. (Greasing the seal with a little petroleum jelly certainly helped.)

The leakage from the bottom hose was caused by fluff/lint debris blocking the bottom aperture to the condenser. Inspecting this will show a plastic double- walled box with one aperture half-way up. The bottom one is not obvious and can be seen by shining a lamp from the bottom up. It does not take too much debris to block this hole; hence the tell-tale small leakage that might go unnoticed until eventually the red-light comes on etc. A piece of bent wire can clear this leakage and then wash everything through so that your dried clothing will be as clean as when the machine was new. Once the condenser is back in place-the raised ring should not be visible if it is pressed home properly The fan-box aluminium to plastic seal need to be carefully remade: don't trap the rubber strip and good silicone rubber will ensure the seal works. The four hoses should all be back in place and don't use lubricant when replacing them as they are quite confined and could come off during use of the machine. You have now made a saving of at least £160. Good luck.

on Feb 17, 2015 | Miele Washing Machines

1 Answer

The water hose keeps blowing off every time I try to use the machine but I cannot manually adjust my water pressure, is there a stronger way of securing the water hose to the machine?

If you're referring to the supply lines I'd be very concerned that the overall pressure in your home is too high. Even if you manage to secure to hose somehow, a fitting inside the washing machine might let go from too much pressure and you'd have a major cleanup disaster on your hands.

See if you can borrow or find someone that has a water pressure gauge - they just screw on in place of the hose. If you read much more than about 60psi, I'd suggest putting a whole house pressure reducer on the water lines.

The attached picture is the type of gauge I'm referring to.

25562027-kkzqnwoljcenh0ozgq2zu55j-3-0.jpg Good luck.

Mar 13, 2015 | Washing Machines

1 Answer

My hitachi washing machine BD-W80 MV shows error F60 on the screen. It stopped washing and can't continue. How to solve the problem?? Thanks

Never seen that code before? Hope it's not something major? The manual for this unit does not cover this error code, so unfortunately you will need to contact Hitachi

Feb 22, 2015 | Washing Machines

1 Answer

Hoover 210 Heavy Duty Washing Machine timer grinding and easy is it to replace?

Make sure you have the right replacement part when you try to replace it. Take a picture from all angles before you disconnect anything. label each wire along with a sequence starting from a reference point. Double check. Then start to remove wires from the timer. Remove the timer and fit the new one. Replace all connections using the labels you placed. Double check with reference to the pictures.

Jan 10, 2014 | Washing Machines

2 Answers


visit and enter your model number and select manuals to order one

Feb 18, 2011 | Washing Machines

1 Answer

When we put clothes to wash, it takes water, spin but at certain point does stop and water does not drain to take more clean water. it happens at one certain point.

Check to see if your model has a drain filter in it. It will be located inside the compartment betwwen the pump and the drum. If it has one chances are it is plugged somewhat and just needs to be removed and cleaned.

Nov 21, 2010 | Kenmore 22422 Top Load Washer

5 Answers

When I turn on the machine, it begins to fill with water. Water then (before the machine would be full) pours out of the tray area where you add the HE detergent. Anyone know a potential fix?

The leak is due to a clogged, small, plastic screen filter located in the cold water hose attached to the back of the washer.
Remove the filter, clean it, place back in hose and reattached hose to washer.
To make the process easier, you can also place a hose filter in the end attached to the cold water faucet so that you don't have to pull the washer so far from the wall.

Check/clean that strainer/filter several times a year.


Mar 26, 2010 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Where is the belt. we have no manual

The belt is located inside the machine at the bottom. you will need to remove the front panel.

you did'nt provide the full model number off the machine. so im giving you my best shot.

use a puddy knife between the front pannel and the lide in the front right and left area to release the clips on both sides and this will let the lid come up or the pannel pull out.

you need to remove the pannel for access.

Jan 11, 2010 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides