Question about Dryers

1 Answer

Tumble dryer Creda tumble dryer does not get hot, elements are ok.

Posted by on

  • Anonymous Apr 15, 2009

    my creda simplicity condenser dryer t622cw has no heat, so there for can not be used and i dont know whats wrong with it

  • Anonymous Mar 20, 2014

    no heat

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 126 Answers

Check the thermostats. Could also be a reset-able overheating thermostat that needs to be reset.

Posted on Jan 28, 2008

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
barkencoa
  • 3463 Answers

SOURCE: No hot air from my tumble dryer

Hi.
You do not state whether it is a condenser or vented dryer.
the most obvious reasn for no heat is element and/or stats..
The only way to confirm which it is-- is to meter them out with a multi meter..
If you have one then set it on the ohms range and test the components for continuity, you should get full scale deflection if they are o/k.
You must disconnect the wires to the components, or you will get a false reading, and needless to say, have the m/c unplugged.

If all test o/k then the problem could be with the timer and or control unit, or the heater relay if it has one.Unknown to me as I do not know your model number.
If it is a condenser dryer, make sure all filters are clear, air intake and outlet vents clear, water container empty .
Plz rate my solution
Thanks

Posted on Dec 29, 2008

rpbuice
  • 161 Answers

SOURCE: no heat to tumble dryer

Check the thermal disc with an OHM meter. One will be next to the heat element (high limit) and another on the air exhaust area which is the low limit.

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the element in a t522vw creda dryer


http://www.ehow.com/how_2087872_replace-belt-creda-tumble-dryer.html

May 28, 2011 | Dryers

1 Answer

How to fit creda thermostats


It depends on which make and model of tumble dryer you have as to how easy it is to replace the relevant parts. Some tumble dryers have heating elements that are easily accessible by removing the back panel, and can be tested for continuity or checked for obvious burning out or open circuit. Others though have their heating elements inside, which aren't accessible without stripping the dryer down we will try and cover as many as possible in or video tutorials section. Tumble dryer heating elements are always protected by thermal fuses and thermostats which are usually simple devices with 2 wires connected and have a bimetal strip inside them. They can be tested for continuity with a test meter.
The problem is that if a stat (thermostat) or t.o.c. (thermal overload cut-out) has gone open circuit, it may be for a reason. Overheating could have caused it by not being able to vent the air due to a blockage some ware. Blocked filters or even the machine not being allowed its ten minute cooling down period, Overloading can cause it as well. Sometimes they can go for no apparent reason. A blocked or severely kinked vent hosecan also cause overheating.

You-Tube video "ymXmpyVkxIE" placeholder (do not delete)


Jan 02, 2010 | Dryers

2 Answers

My creda reverseair tumberledryer won';t work. my


Hi

If you can hear the motor running and have also checked the belt tension and they are O.K., then the only thing I can think of is the Motor pulley, where the belt sits on.

Check that out and make sure it is not loose on the motor shaft, so that the motor turns but the pulley slips.

Regards
Ash

Nov 09, 2009 | Creda IWD12 Front Load Washer / Dryer

1 Answer

Creda tumble dryer T632CW is not heating up. Any


SOUNDS LIKE YOU NEED NEW HEATING ELEMENTS.

Oct 18, 2009 | Dryers

1 Answer

Hi, I ahve a creda tumble dryer T60CW which has sunddenly stopped getting hot. Is this a problem I can fix or do I just by another


It is more than likely going to be one of 2 things, the stats and /or the heater element need replacing.
You will find these located behind a removable panel at the rear of the dryer.
You need a meter to test them for continuity, it is more likely to be the stats as opposed to the heater element.Disconnect 1 wire from each stat to test them.
Plz rate my solution.
Thanks.

Jan 14, 2009 | Dryers

1 Answer

No hot air from my tumble dryer


Hi.
You do not state whether it is a condenser or vented dryer.
the most obvious reasn for no heat is element and/or stats..
The only way to confirm which it is-- is to meter them out with a multi meter..
If you have one then set it on the ohms range and test the components for continuity, you should get full scale deflection if they are o/k.
You must disconnect the wires to the components, or you will get a false reading, and needless to say, have the m/c unplugged.

If all test o/k then the problem could be with the timer and or control unit, or the heater relay if it has one.Unknown to me as I do not know your model number.
If it is a condenser dryer, make sure all filters are clear, air intake and outlet vents clear, water container empty .
Plz rate my solution
Thanks

Dec 29, 2008 | Dryers

1 Answer

No heat to tumble dryer


Check the thermal disc with an OHM meter. One will be next to the heat element (high limit) and another on the air exhaust area which is the low limit.

Dec 16, 2008 | Dryers

1 Answer

No heat in tumble dryer


Is this a gas dryer, if so check the thermal fuse, should be white plastic with 2 wire ports. These tend to bad first. Thanks Dave www.washermd.com

Dec 16, 2008 | Whirlpool GEW9250 Electric Dryer

2 Answers

CREDA TCR2 TUMBLE DRYER


put it in the bin

Sep 12, 2008 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Brad Brown

Level 3 Expert

17473 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...