Question about Protech Systems FasNSeal FSWMKE4 4" Vent Kit for Wall Mounted Boilers & Wat

1 Answer

BOILER SYSTEMS - Protech Systems FasNSeal FSWMKE4 4" Vent Kit for Wall Mounted Boilers & Wat

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

More info req

Posted on Jan 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Taco 007 circulating pump stays on even though boiler shuts down


Don't know your specific unit, but in general, heating systems are two-stage devices:

1: Its too cold: the motorised HW/CH valve moved to the required position, and on achieving it, the circulaion pump starts and the boiler is enabled. (The circ pump may start immediately - its not usually important.) The hot water from the boiler circulates through the heat exchanger and/or radiators until the thermostat thinks its target is warm enough, whereupon it disables the boiler, stops the pump and closes/relaxes the valve(s).

2: The boiler is off while disabled. When enabled, it heats the circulating water to a 'high' temperature and seeks to keep it there. If it reaches that temperature, the boiler will cycle on and off as necessary to maintain the set 'high' temperature. (The circulation pump must run all the time the boiler is enabled.) This may be what you're noticing. Additionally, some boilers will run the circulation pump for a little while after being disabled to reduce the temperature if the water in the pipes and boiler.

Your question doesn't say how the pump running corresponds to thee thermostat settings, but if it were stuck on, I think you'd know!

Dec 31, 2016 | Water Heaters

1 Answer

Protherm


What is the make and model of the boiler?

Jun 03, 2013 | Protech Systems FasNSeal FSWMKE4 4" Vent...

1 Answer

Have protherm 100ec boiler british gas has replaced almost every part boiler will fire temp gauge rises to about 55 flame increase in strenght for about 10sec then boiler cuts out also they keep trying...


Any other symptoms? Is the fault apparent only when drawing hot water? Does the boiler re-light later? Alarm messages? F1? F3 for example?
It may well need a powerflush, but it's best to find out before spending big money with BG.....wish I could get away with charging that much for a flush!!!
FYV

Jan 27, 2013 | Protech Systems FasNSeal FSWMKE4 4" Vent...

1 Answer

Boiler coming on,on its own


Sounds likely. But check the timer selector switching [on/off/24hrs] & if you have a room thermostat wired in

Jun 13, 2009 | Protech Systems FasNSeal FSWMKE4 4" Vent...

1 Answer

Very Hot water coming out of overflow pipe


Is your boiler heating your domestic hot water if so i would turn water off to water maker and see if your boiler pressure stays down below 20 psi. If so water maker is bad. The other thing that could cause this problem would be the boiler pump is out.

Jan 22, 2009 | Protech Systems FasNSeal FSWMKE4 4" Vent...

1 Answer

Open vent central heating


yes it is possible toupgrade the system to a sealed one using a system boiler as you mentioned. the thing to bear in mind is to upgrade the radiator valves to pressure rated ones 10bar.
The probable cause of the over heating is down to the system being sludged up/cold feed blocked, or possible pump circulating problem?
I would recommend the installation of a magna clean filter to help keep the new boiler clear from system debris.I would definately power flush the system, if the system is a twin two port valve system then a automatic bypass should be fitted, all of this done by a corgi registered gas engineer

Kindly

Richie

Dec 18, 2008 | Protech Systems FasNSeal FSWMKE4 4" Vent...

1 Answer

Gas boiler


hi sounds as though the system is sludged up & needs power flushing.the reason is that the water cannot circulate so over heats & pumps into the header tank.
expect to pay approx 350 400 pounds to have it properly cleansed, it will restore the system efficiency.
The other area worth considering is that it could be a faulty pump os that when th eboiler fires it cannot circulate so in turn expands & vents into the tank.

My advise is to arrange for a corgi engineer to sort it out for you.

Kindly

Richie

Dec 17, 2008 | Protech Systems FasNSeal FSWMKE4 4" Vent...

1 Answer

Boiler


this is a drain valve -like a water tap just close clockwise firmly -please advise me - there are some things you have to do now- please respond asap

Oct 31, 2008 | Protech Systems FasNSeal FSWMKE4 4" Vent...

Not finding what you are looking for?
Protech Systems FasNSeal FSWMKE4 4" Vent Kit for Wall Mounted Boilers & Wat Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Protech Systems Water Heaters Experts

Brad Brown

Level 3 Expert

17436 Answers

Paul Carew

Level 3 Expert

3328 Answers

Gil Shultz

Level 3 Expert

3382 Answers

Are you a Protech Systems Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...