Question about Kohler 1014-H2-96 Portrait 5' Whirlpool Bath Tub Finish: Biscuit

1 Answer

What is the round filter like attachment with tons of little holes on the inside my tub and how do i clean it

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

It is called the suction intake- the pump sucks the water in through the suction intake. It serves as a hair and particle trap (safety device). Some suction intakes can be unscrewed counter-clockwise, others have a round cover that can be popped off with a flathead screwdriver (the cover conceals a philips head screw).

don@crownbath.com

Posted on Dec 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WE NEED OPEN THE WAHINE MECHINE DOOR


there is a round cover at bottom front that will come off with a quarter turn to left or anticlockwise. inside you will see a metal clip with a wire attached to it. pull the wire and your door will unlatch the magnetic lock. Your door most likely is in alarm from water remaining in the tub. There is a drain plug in the same hole and behind it is a drain fluff or filter that is most likely plugged. Clean this out well replace the plug and fluff/filter. When reinstalling plug make sure all sand and debris are out of the threads and apply light oil before screwing the plug back in. If you don't do this you run the risk of breaking the cap handle which results in having to buy the whole pump unit to get a new cap.

Jul 29, 2016 | Bosch Washing Machines

1 Answer

How does water actually get into the tub of a GE Model GSD2200G00WW dishwasher and to clean the overflow area how do you get it out I have cover off, down to rubber, got some stuff out, ? filter


First--Water enters the dishwasher through the water inlet valve which is the plastic electric valve that the house plumbing attaches to. On GE's its usually under the left front corner once you remove the small access panel. Power is applied by the the timer during the fill cycle. Second-- there is no other filter down in the area you are trying to clean. To remove that rubber boot/sump area you would need to un-install the dishwasher and remove the motor pump assembly from underneath. Here are a couple of things to check for poor cleaning. 1---internal water level---should be about 1/2 inch at door front edge. If not, that inlet valve may be partially blocked and need replaced. 2---water temp needs to be at least 120 minimum. If not hot enough it will not dissolve soap. 3--- look closely at all the little holes in the spray arms. Pay close attention to the end holes that are used to spray out water like a jet engine and spin the arms. Any blocked holes need to be cleaned with something like a toothpick. 4--- check dishwasher at cycle end. If tub has excessive amount of water left inside you may have a blocked drain hose from dishwasher to house drain system. Remove and clean. A small amount of water in sump area is normal but none u near door.

May 02, 2015 | GE Dishwashers

1 Answer

Whirlpool duet ghw9400pwo sometimes stays on rinse, sometimes shows sud , sometimes f2 code. My repairman cleaned filter by pump but he feels its the control board


Well, before you go investing in a new control panel that probably won't fix your F02 (Slow Drain)/SUD problem, or investing in a new machine that you may not need, I would remove the line that connects the tub basin to the pump filter. Make sure its clear (and it probably is if your filter is clear). It attaches to the tub basin via a hose clamp that is easily removed (though not so easily re-installed, speaking as a woman with fairly short arms and little hand strength). Once its removed, stick your hand up into the drum basin. I would suspect that you'll pull out a ton (okay, well maybe just a few cups) of yuck that is causing your F02 (Slow Drain)/SUD issue. Once you clean it all out, put it all back together and give it a test run.

Feb 18, 2013 | Washing Machines

1 Answer

All the holes arround inside the tub/basket seems to be blocked or is this a filter


No your drain is pluging up and needs cleared.What you are seeing is link from backwashing. Try runing some vinegar through a wash cycle and clean your drum

Feb 25, 2010 | Whirlpool Washing Machines

1 Answer

How do I get change out of the washer? It went


I think you are talking about the three tub baffles that are attached to the inner tub. You can remove the baffles, usually one or two screws hold these into the tub. If it only has one screw then the opposite end is clipped into the tub. Most coins however get flushed down into the drain pump filter. We call this a coin catcher as that is what it is designed to do. Remove the front bottom panel, 3 to 4 screws on the bottom. Put a towel down under the pump to catch about a half gallon of water. There is a large round plastic screw that you unscrew from the pump assembly. The screw is three to 4 inches in diameter and almost dead center on the bottom front of the washer. Once you have unscrewed the unit, pull it out and clean out everything you see. Look inside and make sure there is nothing in the hose or the pump inlet hole. Reinstall and test for leaks before you put the panel back on. I recommend you clean this out every 6 months. Good Luck,
Appliance Specialists

Dec 11, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Broken drain pipe under washer tub


Well,i wouldn't solder the old pipe back on.You could replace the pipe or replace the tub entirely.But you're looking at about the same price to repair an old machine for the price of buying a new one.techs come at about $50 per hour and you're looking at about an 8 hour day to repair it.a new machine should run you about $ 400 to $ 500.

Oct 13, 2009 | Maytag Performa PAV2200

1 Answer

The Aprilaire is leaking around the casing attached to furnace


How old is the filter? Filters should be replaced every year. If its a new filter check to make sure the little hose is inside the hole at the tom of the filter.

Jan 18, 2009 | Humidifiers

2 Answers

Pressure but no water


Hi,

Make sure your filter is clean, take the filter and head it to light. If it is clean then you can see a little hole in the midle.

Aug 09, 2008 | Breville ESP8XL Espresso Machine

2 Answers

How to locate and clean the lint trap


Top load washing machines do have lint filters, they used older models have trays that sit on top of the agitator. Newer ones aren't as obvious and are attached to the bottom of the inner tub. If you remove the agitator, you'll see a bunch of holes in the bottom of the tub, the filter right behind these holes. Cleaning/replacing it involves removing the inner tub, so it's not an easy task. It is likely that by the time you're having problems with the filter, it will be beyond cleaning and will need to be replaced. Considering all the trouble it takes to get to, you might as well.

Sep 30, 2007 | Washing Machines

Not finding what you are looking for?
Kohler 1014-H2-96 Portrait 5' Whirlpool Bath Tub Finish: Biscuit Logo

518 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kohler Home Experts

john h

Level 3 Expert

17852 Answers

Mike

Level 3 Expert

4356 Answers

Steve Wood Plumbing...
Steve Wood Plumbing...

Level 1 Expert

21 Answers

Are you a Kohler Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...