Question about Hobart D300 Stand Mixer

3 Answers

The shaft snapped off the end of the motor in this mixer. Anyone know if these motors can be purchased anywhere or fixed?

Posted by on

  • 1 more comment 
  • dgealey Dec 27, 2009

    Thanks for the reply. I contacted this company,and they don't have motors or armatures. Any other suggestions?

  • dgealey Dec 27, 2009

    Thanks for the links. I'll check them out.

  • dgealey Jan 16, 2010

    I called BigTray, and they say they only sell equipment, not parts and couldn't help me. Diamond WebDesign isn't accepting any new customers. Thanks for the suggestions, though. Do you know of any other companies that might sell used armatures (old Hobart parts)?

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,515 Answers

Hi , I did some research and found nothing on repairing, but you can purchase new and refurbished ones. They may be able to tell if it can be repaired. Here is two Links: www.BigTray.com. They can and will solve your problem.BizRate.com/hobart also will give you a lot of information on this Mixer. I am glad I could be of help to you.
Sincerely,
Shastalaker7

Posted on Dec 27, 2009

  • 1 more comment 
  • Robert Horton
    Robert Horton Dec 27, 2009

    Let me check and see what I can come up with. I checked the site out myself and they said they handled the hobart, strange. I will get you to the right place.
    Sincerely,
    Shastalaker7


  • Robert Horton
    Robert Horton Dec 27, 2009

    Hi, Try this site as they deal in parts shafts transmissions for Hobart mixers, bearings and so on:
    www.diamond-webdesighns.com/rsr-parts-catalog/email.htm
    I am sure you will find what you are looking for here. Please let me know on this as I have checked it out and they show full page diagrams also.
    Good Luck, Sincerely,
    Shastalaker7


  • Robert Horton
    Robert Horton Dec 28, 2009

    Hi, Thank You for the outstanding ratings, this was very kind of you. Please continue to use all of us here at FixYa, as we work hard to solve your problems and come up with solutions that are helpful.
    Sincerely,
    Shastalaker7


×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Hobart Expert
  • 119 Answers

Your local Hobart office can sell you the part.
www.hobartservice.com "Locate an Office" enter you Zip.

Posted on Jul 16, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,741 Answers

Here is the link where you can get all the parts for hobard stand mixer:--
http://www.food-equipment.com/parts_Hobart_mixers.htm
click above link directly to reach parts page with proper part numbers.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Posted on Dec 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cuisinart electric cookie press ccp-10 doesn't press the cookie dough out.


Probably the motor is slipping threads on the drive shaft.

Dec 15, 2017 | Cuisinart Food Mixers

1 Answer

I need a replacement motor on a KitchenAid Professional HD Stand Mixer (Model KG25H7XSL).


The loud pop was probably the soft start circuit board on the motor. You can buy this board at repair sites or Ebay. And yes, they make 220V versions of this mixer.

http://www.samstores.com/product-kitchenaid-5ksm5ebu-heavy-duty-mixer-for-220-volts-%28cobalt-blue%29-16220.html

Dec 31, 2012 | KitchenAid Food Mixers

1 Answer

Kitchenaid stand mixer motor is dead and mixer won't turn on


Hello,
There are a few reasons this might happen from ugly to easy lets start with easy and work to ugly.
1. check the outlet you are plugging the mixer into...I know I know but it does happen
2. The cord on the mixer might have a bad connection or one of the flag terminals may have come loose or broke, remember all metal fatigues. If you know how to uses a multi meter an easy check by removing the rear cover and check the power on the contacts from the end of cord that plugs into the wall and then goes into the mixer, you can check by Ohms testing (safer) or by live connection to the outlet in the wall.
3. The brushes on the mixer, one or both may have reached end of life, easy and inexpensive fix. They are under the big plastic screw covers that you see on the side of your mixer. BTW they can only go in one way and if not replaced correctly the mixer will not work even if you have a brand new mixer.
4 The mixer may need a new speed control plate rather more involved because you have to speed tune the mixer after it is replaced but inexpensive and can be performed by anyone from the rear of mixer. BUT!!!! The speed control board may not be bad but only that the mixer needs to be speed tuned.
5. It may be a phase control board gone bad, it is behind the speed control plate, again it can be replaced relatively easily but you also will have to speed tune the mixer and it will be a double digit cost on the part ($25.00-$30.00 unless you go to the internet and search sites, you may find on eBay for 12-15 dollars plus shipping.
6. We are now entering the ugly phase. the items above are all the electric problems that you can fix easily and inexpensively. The next requires a complete tear down of the mixer to replace the Stator and or Armature (the motor). You can do it but it will cost around $60-$70.00 dollars for the motor and then $6.00 for a new gasket which you will need as soon as you open the motor head. Some peeps just re-use the old I would not.BUT!!!!
7. The gears may have stripped while you were using the machine on high and has frozen up so that when you turn it on it won't work. If that is the case then the mixer will have to have the gears and grease and gasket repaired. Gasket=$7.00, Grease=$17-$24.00, it only comes in quarts and you get 30 ounces but only need 6 for a re-grease, Gears, there are 3 and they run between $10.00 for one and up to $30.00 for the pinion tower. No way to tell from the info you sent.
I have been fixing kitchenaid mixers for a while and I am only now replacing my first motor. So I think it is an easy to intermediate fix, DIY could spend 3 hours doing and spend $30.00 bucks on parts. The ugly $150.00 to $175.00 and I would recommend a service center do the motor because they will check all gears repack grease install new gasket and do a speed tune when they fix it.


Kitchen aid mixers are great and sometimes need a little TLC and they will last for years and years. If you could explain further exactly what happened during the speed run up and what you were mixing and what model and serial number (can be found on white sticker under base of mixer in the base cavity). then I may be able to narrow down the repair / fix path. If this helps at all please let us know we like to hear if we are able to help.

Sep 18, 2012 | KitchenAid KP2671 Professional 6 Series...

1 Answer

Braun Vario 280 Watt type 480 hand held blender. The bowl top that the hand mixer fitsd into is frozen. The hand held motor works but the shaft in the top that turns the blade is frozen. I don't...


HI.This steps might be as well helpful.let me just clarify that you can't even manually twist the shafting.If the motor is working an yet it will not turn the shaft.Tha shafting bossing might as well been broken misallign inside..Better remove the cover by unscrewing it and then try to observe how the motor works.If it really does turn when ever it is plugg on to the source.Observe also misallign bosssing that connects the shafting and the motor's rotor.Thank you for choosing FIXYA.

Aug 16, 2011 | Braun M880 MultiMix Hand Mixer

1 Answer

Motor speed is erratic. Now it makes grinding noises


There is a speed governor on the motor end of the armature (back end of the motor) that may
need replacing. It's one of the few parts still available. on eBay, or mendingshed.com

The grinding could either be the gears in the beater end of the mixer, or the motor bearing on
the back end of the motor.

The gears are available as they are the same as for newer mixers like the K5SS.

The motor end bearing is not available, but I was able to take the bearing out of the motor
bearing plate from a K5SS which is still available, again on eBay or mending shed, and put
it in the motor bearing plate for the K5A. Then you need to soak the felt ring inside the housing
on the back end of the bearing in oil, preferably synthetic like Mobil 1. Also helps to smear
a little moly grease (not out of a tube, not enuf moly content - get some Honda Moly 60, small
tube for $10 at any Honda store) on the shaft when you have it apart.

Jan 21, 2011 | KitchenAid Classic Stand Mixer

1 Answer

Leaking oil from the mixer head. Occasionally find a drop of oil has collected on the end of the mixer shaft. What is the cause of this problem and can parts be ordered so I can fix it at home?


This is the end seal of the motor, you can get parts from manufacturer. you will need a service manual, OR go to the manufacturers web site and contact them.

Mar 18, 2010 | KitchenAid KSM90 Ultra Power Series Stand...

2 Answers

Crypto Peerless Dough Mixer Diving Key broken


have you solved the problem , if not phone heartland catering spares 0121 243 3336 they specialise in crypto

Oct 23, 2009 | Food Mixers

2 Answers

I have disassembled my K5SS Kitchen Aid mixe with all gears removed in order to solve its electrical problem. When I plug in the motor and move the speed lever, there is no movement or sound of the motor...


Unless it sits at the back of the motor behind the vent cover. I couldn't find one anywhere on ours either. Check the motor brushes for broken or badly worn carbons, or collapsed springs. It could be a broken wire at the plug end or something wrong with the speed switch. Some strategic voltmeter sleuthing is required. Try turning the motor shaft while the power is on. It may have a dead commutator segment.

Aug 25, 2009 | KitchenAid K5SS Heavy Duty Commercial...

1 Answer

Parts needed for Matfer 660 Watts 210412


Heritage Food Service Equipment has parts listed as available. www.hfse.com
The motor to shaft coupling will have to be ordered from another stlye motor but will work.
The model to look for is actually listed as Dito-Dean, not Matfer.

Nov 10, 2008 | Matfer 660 Watts 210412 Hand Mixer

2 Answers

Beater keeps falling out. The plastic thing at the top of the beater inside the mixer needs to be replaced. Where can I get the part?


Sunbeam 2366 stand mixer -- Front view: mixer-0-small.JPG -- 0d345a3.jpg-- image of the "beater clip": mixer-1-small.JPG -- notice the wear on the plastic clip --8982711.jpg -- image of the "modified" beater: mixer-2-small.JPG - I took a paper clip an wound very tightly to the smallest diameter (notice it covers the entire section to prevent slippage) and then put one wrap around the "top knot" to increase diameter --d67ddea.jpg -- image of the back of the front cover: mixer-3-small.JPG - notice the broken clip at the top. I used a wide scrapper blade to separate the cover from the main body. 3297c2c.jpg----

Oct 16, 2008 | Sunbeam 2366 MixMaster Series Hand/Stand...

Not finding what you are looking for?
Hobart D300 Stand Mixer Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1309 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1896 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...