Question about Dryers

1 Answer

We are trying to remove our heating element in our speed queen dryer model no.AEM497W2. Can you tell me how to do this? thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 135 Answers

Try this web site

http://www.repairclinic.com/RepairHelp/RepairHelp.aspx

Hope this helps

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing heating element speed queen


unplug dryer , pull front off two screws at bottom element in back lower left corner two screws hold remove and replace

Nov 26, 2013 | Kenmore NEW Replacement Part - Whirlpool /...

1 Answer

Dryer wont heat


The only thing left to check is the voltage at the heating coil. IF it is not present then the timer or relay is bad.

Jul 22, 2013 | Speed Queen AES17AWF Electric Dryer

1 Answer

I DONT HAVE A GAS DRYER AND I JUST BOUGHT A HEATER ELEMENT JUST DON'T KNOW WHERE TO PUT IT ON MY SPEED QUEEN DRYER


Hello,

If does vary by model of SpeedQueen dryer,but typically the heat element fit in the bottom or the rear plate the supports the drum..reply with model number and i will tell you where yours goes.

GENE

Sep 04, 2011 | Speed Queen AES68AWF Gas Dryers

2 Answers

I have a speed queen electric dryer model number aem45300. problem the dryer runs but does not heat. We cleaned out all the area that contained lint. Is there a reset button for the heating element in...


There is no reset button, check yoru breaker, by turning FULLY OFF (somewhat forcefully off) then back on and test again.

All thermal limiters will auto reset when cooled...

Mar 04, 2011 | Speed Queen AES17AWF Electric Dryer

1 Answer

Dryer will not heat up Does run


It's probably the thermostats that are normally attatched to the element or it could be the element itself. They are nprmally placed in the rear of the appliance.

The thermostats will only cost a few pounds.

Mar 12, 2010 | Speed Queen Dryers

1 Answer

Speed Queen Model #NE4513LF just stopped heating. Can the heating element & thermal switch be tested. If so, how many ohms should they both measure? Any other solutions would be appreciated.


The thermal will read '0' ohms through it if it's good. The element will vary depending on it's wattage. A 5000 watt element will read 11.5 ohms.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Jul 06, 2009 | Dryers

1 Answer

Dryer doesn't heat up at all


hi..the reason to this problem may be due to two reasons.
It may be either thermostat or the heating element.
check this out..
thank u..
kindly rate my response..

Jun 27, 2009 | Speed Queen AES28AWF Electric Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

83593 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Brad Brown

Level 3 Expert

17634 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...