Question about Dyna-Glo Heating & Cooling

Open Question

I have a dyna glo workhorse 65000 btu it will light but wont stay running it only stayes running foa about 1 minut than the light starts blinking

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: E 1 error on Dyna-Glo Workhorse Kerosene Turbo Heater

You might have dust in the pilot orfice . If you do the pilot flame curves up and dosen't touch the thermo coupling enough .

Posted on Feb 24, 2008

Ad
  • 1 Answer

SOURCE: won't stay lit

here is a site that sells parts http://www.thoseheaterguys.com/1933204.html here is a manual and parts list http://www.rentrain.com/library_files/400.pdf . hope this helps.

Posted on Jan 14, 2009

  • 4 Answers

SOURCE: dyna-glo kerosene heater (rmc-55-r7 )

wicks won't light for usually one of 2 reasons. water in the kerosene, which means a new wick and new fuel. or build-up on the wick. check to see if the wick is hard. your wick should be soft. burning out the heater until all fuel is used either by running down all the fuel in the unit or removing the fuel can and lighting to burn off all fuel in the bottom will prevent the wick from getting hard.

Posted on Jan 19, 2009

  • 3351 Answers

SOURCE: Dyna-glo parts

thermocouples you can buy from any heating spares oulet or national energy a hone well is most common for useing as a replacement

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: dyna glo workhorse heater

you need to pull top cover off. And bend the igniter in to the spray of fuel and check the gap of the ignighter to 3.5 mm and bingo should work i just bought one and had to do this to it

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a dyna glo RMC 40 NGT vent less wall heater that I would like to convert to propane, I need to know which conversion kit to buy, and where. Thank you.


dyna glo natural gas heater Questions & Answers - Fixya

www.fixya.com > Forum > Tags
dyna glo ventless rmc50 ngt can this heater be changed from natural gas to propaneuse, ... Dyna Glo Natural Gas conversion to LP Gas I have a Dyna-Glo natural gas space ... Question about D-E36 Infra-Red Wall Mounted Panel Heater ... dyna glo heater model #RMC-40GT I believe on your particular model , that you ...

Parts for Dyna Glo, Thermoheat and Dyna Glo Pro Heaters

spaceheaterparts.com/category.sc?categoryId=13
Shop Dyna Glo, Thermoheat, Dura Heat, Workhorse LP and oil fired htrs ... Circuit Board 2201181 Dyna Glo & Thermoheat 150k Nat Gas Htr RMC-FA150NGDGD ... This spark plug (ignitor) is used on Dyna Glo and Thermoheat 40K btu LP.

Propane Wall Heaters - Walmart.com

www.walmart.com > ... > Heaters

WalmartDyna-Glo IR18NMDG-1 18,000 BTU Natural Gas - Infrared Vent Free Wall Heater. $170. ... Dyna-Glo 40K Liquid Propane 360-Degree Tank Top Heater. $88.00 ... Dyna-Glo Deluxe RMC-FA125DGD Portable Gas Powered Forced Air Heater.

1352062 Dyna Glo Natural Gas conversion to LP Gas

162.220.53.34/F/.../t1352062-dyna_glo_natural_gas_conversion_lp_gas

Jan 12, 2016 | Heating & Cooling

1 Answer

Dyna-Glo 360 will light but wont stay on


reset your thermostat your temp may need set up higher .

Feb 21, 2015 | Dyna-Glo Heating & Cooling

1 Answer

Fuel shut off switch


Replace the thermostat.

Jan 23, 2014 | Dyna-Glo Heating & Cooling

1 Answer

Have dyna glo forced air kerosene heater, 65000 btu. It's about 10 years old. Not getting fuel to nozzle. Cleaned fuel filter; replaced hoses; cleaned nozzle. air pressure gauge shows pressure OK.


Are the hoses on the fuel nozzle right. Air hose to the front and fuel to the rear. Did you remove the nozzle from the adaptor to check the o-ring? Let me know what you find.
nitensheaterservice@earthlink.net
Niten's Heater Service on Facebook

Jan 13, 2011 | Dyna-Glo Heating & Cooling

1 Answer

Pilot will not light- rmi-80ngt-30,000 btu


if it wil light and wont stay lit replace your thermal coupling

Jan 23, 2010 | Dyna Glo "" Natural Gas Heater Mn200tba

1 Answer

Dyna-glo parts


thermocouples you can buy from any heating spares oulet or national energy a hone well is most common for useing as a replacement

Feb 03, 2009 | Dyna-Glo D-E36 Infra-Red Wall Mounted...

1 Answer

Heater won't stay running


found a web site that didn't want to charge for information.

Sep 23, 2008 | Dyna-Glo Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

833 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dyna-Glo Heating & Cooling Experts

Paul Carew

Level 3 Expert

3351 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

fordexpert

Level 3 Expert

5690 Answers

Are you a Dyna-Glo Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...