Question about Baumatic BWE40 Wine Cooler

1 Answer

Code E2 showing in temparature display

The Code E2 is showing in the temparatue disply window. I can't find my instructions. Bottles still apper to be cool. Is this anything to worry about ? If so what can be done?

Stuart Hatton

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer
Re: code E2 showing in temparature display


I contacted the technical team at and here is the reply I got.

-----Original Message-----
From: [] On Behalf Of
Sent: 25 January 2008 13:02
To: Taline Bedrossian
Subject: Re: BWE40 wine cooler

Good Morning.
Thank you for your e-mail.
This error code means that your appliance has experienced a defrost sensor
fault. Please contact our service team on 01189 336 911 to arrange a
suitable time for an Engineer to visit you.
Kind Regards

Quality and Technical Department
Baumatic Ltd

Posted on Jan 25, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

BWE40 wine cooler. Is it safe to leave it switched on when code e2 is showing? Does code e2 distinguish which of the two sensors need replacing? Thanks.

e2 is a temperature sensor error code.
You would need a multimeter to test sensor and control board.
Either could be the problem

May 11, 2014 | Baumatic BWE40 Wine Cooler

1 Answer

Instruction manual for dihl wine cooler 32 bottles

i have a dihl 21 bottle dual control wine cooler. the temperature display keeps flashing and won't set, this is now happening with both top and bottom ... how do i fix it

May 18, 2012 | Refrigerators

1 Answer

Roper Range error code message with beeps for F1 E2

F1 - E2 UL A/D error(s)

1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Aug 20, 2011 | Roper Refrigerators

1 Answer

Errorcode EE in display. Whats wrong?

E1 - Freezer thermistor open circuit.
E2 - Freezer thermistor short circuit.
E3 - Fridge thermistor open circuit.
E4 - Fridge thermistor short circuit.
E7 - Evaporator thermistor open circuit.
E8 - Evaporator thermistor short circuit.
E9 - Temperature set switch open circuit
EA - No feedback from Baffle
EB - Fridge Baffle motor operating continuously
EE - Defrost time out

This was the only code listing with an EE error code - which is a Hotpoint - so if your's isn't a Hotpoint it is probably incorrect.

If you do have a Hotpoint Refrigerator then either the defrost timer is not functioning correctly or your heater element is malfunctioning.

Jun 20, 2011 | Refrigerators

1 Answer

Avanti error code e2 wine chiller, what is the problem?

Display flashes Error message "E2" - Defrost sensor (Coil Sensor) failure.

Contact the Avanti Service Department - 1-800-220-5570

Hope helps.

Jun 03, 2011 | Avanti WC42 Wine Cooler

1 Answer

E2 on display panel not cooling


For this error code E2, you need to replace the main board WR55X10656. There is no other solution, and it will cost you $300.

Hope this helps.


Apr 24, 2011 | Refrigerators

1 Answer

Error code "E2" of Gorenje K357

E2 - reporting a problem with the sensor of the evaporator in the refrigerator / in isolation 10_9_2011_3_02_24_pm.jpg

Jun 03, 2010 | Gorenje K357 / 2 Bottom Freezer...

1 Answer

HOTPOINT MISTRAL plus 8596 fridge E2 code

Go to this site:

Type "Mistral Thermistor" into the search and help will be availible. You have a very common problem which is an easy fix in most cases. Good luck.

Mar 13, 2010 | Hotpoint Refrigerators

1 Answer

Doesnt seem to be getting cold. The letter

Dear Ray,

Are you sure this is an 60RDE and not a 60RD? I don't remember the "L" code for the new control/display. The older unit (pre-2007) would show an "L" for compressor lock-out. The newer display normally shows codes like "E1, E2 through E4" which stand for compressor high/low amps, Condensor fan low/high amps, Control thermsitor failure and display thermsitor failure" in that order. I would call the factory at 800-223-3900 (8:00 to 5:00 EST) and ask for technical assistance. Talk to Tim Malloy or Ron Peterson (first contact). If they can't help you ask for John Damouth (the engineer who knows those controls better than anyone)

In the meantime...try a power reset (turn off the circuit breaker or un plug it for 10 seconds). If it resets it could be a loose connection somewhere. If not....well hopefully they can help you with that.


Jan 30, 2010 | Marvel 60RDE-BB-F/60RDE-WW-F Compact...

1 Answer

Bosch Fridge Freezer KGU32

E2 indicates failure or out of tolerence evaporator sensor which is foamed in and not replacable. The only repair posibility is replacement of the electronic control board which now ignors input from the sensor

Aug 11, 2005 | Bosch KGU32124 Bottom Freezer Refrigerator

Not finding what you are looking for?
Baumatic BWE40 Wine Cooler Logo

3,281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baumatic Refrigerators Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21840 Answers

mike cooper

Level 3 Expert

864 Answers


Level 3 Expert

5954 Answers

Are you a Baumatic Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides