Question about Philips DVD 622 DVD Player

1 Answer

Progressive Scan When Progressive Scan is enabled does the video play from the Component Video port?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 8,596 Answers
Re: Progressive Scan

Only if the source is 480p - otherwise it will not give you a picture

Posted on Sep 04, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do you get higher than 480p resolution on playback?

Hi Chuck, I copied this from the MWD7006 manual - I hope it helps.

If your TV is compatible with 525p (480p) progressive scanning and you want to enjoy that high quality picture, you must use Component Video cable connection and progressive scanning mode.

To set the mode, set "PROGRESSIVE" to "ON" in SETUP menu, so that the "P-SCAN" indicator on the front panel lights up.

When "PROGRESSIVE" is "ON", video signals from the unit's VIDEO OUT and S-VIDEO OUT jacks will be distorted or not be output at all.

If your TV is not compatible with progressive scanning, use this unit in interlace mode and set "PROGRESSIVE" to "OFF" either in SETUP menu, or by pressing and holding [PLAY B] on the front of the unit for more than 5 seconds, so that the "P-SCAN" indicator on the front panel lights off.

Download Magnavox MWD7006 Owner Manual

Jan 25, 2014 | Philips Magnavox MWD7006 DVD Player

1 Answer

Formats for dvp-ns70h

selectable 720p/1080i output via HDMI digital interface (separate adapter available for TVs with DVI input)
selectable progressive-scan mode for smoother video with HD-compatible TVs (via the component video output)
optical and coaxial digital outputs for Dolby Digital/DTS /PCM
  • 1 set of audio/video outputs (composite, S-video, 480i/480p component video, and HDMI)
  • plays DVD-Video discs, DVD-Rs & DVD-RWs, and DVD+Rs & DVD+RWs
  • plays CDs, CD-Rs & CD-RWs, and MP3 CDs
  • plays digital picture CDs (JPEG)
  • remote control (multibrand for TVs)
  • 108MHz/12-bit video DAC
  • 192kHz/24-bit audio DAC

Oct 14, 2012 | Sony DVP-NS70H DVD Player

1 Answer

Hi, I've a small problem cocerning this dv-363 player. I accidentally set it to 'progressive'. Now I cannot undo. I tried holding the buttons on remote and on machine itself, still not working, can you...

Progressive Scan is a menu option relating to video output of this player. Assuming you have the original DVD remote, this should be easy.

* From the user manual (pages 50-51 of the pdf document):

About progressive scan video
Compared to interlace video, progressive
scan video effectively doubles the scanning
rate of the picture, resulting in a very stable,
flicker-free image. Progressive scan video is
available only from the component video

If you connect a TV that is not compatible
with a progressive scan signal and switch
the player to progressive, you will not be
able to see any picture at all. In this case,
switch everything off and reconnect using
the supplied video cable (see Easy
connections on page 14), then switch
back to Interlace. Switch the player to
standby then, using the front panel
controls, press STANDBY/ON while
pressing 'back to Interlace.

Hold these 2 buttons together for about 10-15 seconds or so, but only while the player is in standby mode. *

If you have lost the manual, you may be able to download the user guide (as an adobe reader (pdf) document) from:

(it will ask you for an email address prior to downloading - use a blank address if possible and enter the security code in the fields then save the document)

If the above suggestion does not switch it back to interlace, you will need a TV with progressive scan function to enable you to access the player's on-screen menu and in 'Initial Settings' 'Video Output' 'Component Out' section, select 'Interlace'. and press OK from remote as required.

Either way, it should NOT require a workshop service, and is simple enough to do at consumer level with the right TV type.

Mar 05, 2011 | Pioneer DV-363 DVD Player

1 Answer

I have a HD TV with cable and a go video DVD/VHS player hooked up. I went to change the time and accidentally changed the setting on the DVD player from auto scan (I think) from off to on and now when I...

It sounds like you may have enabled the progressive scan output on your DVD-VHS combo. This is a correct setting if your TV support it. However most DVD players that support progressive scan will not support an interlaced signal and a progressive signal at the same time.

It would appear that you are using a composite type cable (3 RCA ends. 1 for video and 2 for audio) for this hook up. This means you have two choices.

#1 Look in the manual for the unit for the FACTORY Reset option. Its usually a combination of plugging the unit in while holding the power button or something similar to that. Without a model # I can't help any further with this option.

#2 Use a component video cable (3 RCA red/green/blue) to plug your DVD/VHS player into a compatible input on your HD TV. Your TV will pick up the progressive scan output from the unit and give you back your on screen display. At this point you can go back into the menu and disable progressive scan. And now just reverse the process to plug the DVD player back in using the composite cable.

It should be noted that if you have a progressive scan TV which HD TV's support you will get a better picture if you use the Component video cables instead of switching back to the composite cable. If you decide to use the component cables you will still need to run audio cables though.

Best of luck.


Aug 11, 2009 | GoVideo Go Video DVD/VCR Combo

2 Answers

Split screen on DVD player

This sounds like a progressive scan issue (unit in P.Scan Mode) here is a C&P from the manual

Set "Alt Video Out"
Highlight "Alt Video Out", then press the RIGHT button to select
one of the following options:
• S-Video - Select this if you are using the S-Video OUT jack on
the rear panel to connect to a TV.
• Component - Select this if you are using the COMPONENT
VIDEO OUT jacks on the rear panel to connect to a
Progressive(480p) or Interlaced (480i) TV.
• See your TV owner's manual to determine what type of TV you
- Interlace : Interlaced Scan mode will work.
- Progressive : Progressive Scan mode will work, and Video
and S-Video will not work.
• Press the Progressive button on the front panel if you have a
Progressive scan TV only. Otherwise, the picture will be

Feb 04, 2009 | Samsung DVD-V3650 DVD Player/VCR

1 Answer

Progressive Scan

Hold the stop button for about 10 seconds. The other thing to do is move the video out cable at the back of the DVD to one of the component outs (there are three of them one for each color rgb) you will be able to read the menu again. turn off progressive scan and reconnect the video cable to dvd out

Jan 04, 2008 | Zenith XBV442 DVD Player/VCR

2 Answers

DVD recorder: Changed the settings, now

we could go through the setting like, you can see the monitor. using the remote do the following steps:
Step 1. press set up button.
Step 2. press down arrow once. ( playback)
Step 3. press OK.
Step 4. press down arrow once. (video (selection))
Step 5. press OK. (progressive scan)
Step 6. press OK, again.
Step 7. press down arrow once. (progressive scan off)
Step 8. press OK
you have now turned progressive scan off.

Dec 19, 2007 | Philips Magnavox MWR10D6 DVD Recorder

2 Answers

No video output from rca jack or svideo

The problem is with the p.scan button. It seems if its pressed the video goes off. You need to keep it pushed until you see a message for "progressive scan".

Dec 08, 2007 | Samsung DVDR120 DVD Recorder

6 Answers

SD-K530SU - Turning Off Progressive Scan Mode

Once the setting for Progressive Scan output is entered,
an image will only be visible on a Progressive Scan compatible
TV or monitor. If you set Progressive Scan to On in
error, you must reset the unit. Pointing the remote at the
player, press the STOP (x) button to stop any disc that is
playing. Next, press the STOP (x) button again and hold it
for five seconds before releasing it. The video output will
be restored to the standard setting, and a picture will once
again be visible on a conventional analog TV or monitor.

Nov 06, 2007 | Insignia NS-DVDR1 DVD Recorder

Not finding what you are looking for?
Philips DVD 622 DVD Player Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips DVD & Blu-Ray Players Experts


Level 1 Expert

6 Answers

Cindy Wells

Level 3 Expert

4720 Answers

rugby prop

Level 3 Expert

426 Answers

Are you a Philips DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides