Question about Watches

1 Answer

Lost screw My watch is stainless with steel band. The screw holding the second to the top link to the top link (attached to watch) fell out and is lost. I have other band screws but they are too short. Where can I get this screw?

Posted by on

  • jh-hdrider Dec 07, 2008

    I have a luminox titanium sport watch, all 3 screws on 1 side of the band fell out. Can I purchase these screws? This watch was purchased in 2002, I believe it is a 3000 series

  • spagentz28 Feb 18, 2009

    Same problem with my Rado Coupole; and I have been to several jewelry stores and they did not have the proper replacement screw.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,039 Answers

Go to any jewelery store cheers

Posted on Jan 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Looking for band for invicta sea spider 1261..i want to replace it with a stainless steel band..

Sea Spider 1261 INVICTA Sea Spider Men 50mm Stainless Steel Gold Black dial 3600K Mechanical watch located attached link offers multiple compatible straps

Nov 11, 2017 | Invicta Watches

1 Answer

How to change watch band on invicta angel stainless steel band

Turn the watch over and you will see that the band is attached to the watch with spring loaded pins. There is room to put a spring removal tool in the available slot and depress the spring which will allow you to twist the band away from the watch. Be careful to not loose the spring loaded pin as you may need it to install another band. Almost every watch uses this method of band removal. Those that don't usually have a long screw that is accessible from the side of the watch.

Feb 19, 2013 | Invicta Reserve Subaqua Venom Swiss Quartz...

1 Answer

How to remove links from invicta sea spider polyurethane bracelet

You should use two extremely small flat head screw drivers to remove links on Invicta polyurethane watch bands. The smaller pens on the polyurethane watch bands have a notched cap (tiny screws) on each end .You must use one screw driver to hold the pen cap (screw) steady and the other screw driver to turn the cap (screw) counter clockwise. You only have to remove one notched cap (screw). These caps (screws) are very small and you should be careful not to lose them. Once you removed the cap (screws) you can use a small screw driver or paper clip to push the pens through the links. You should repeat this til you remove the desired links.

Nov 24, 2011 | Invicta Sea Spider Chronograph...

1 Answer

Broken Watch band

you probably just need a pin to secure the links back together. an authorized Movado retailer will have the tension or screw pins to put the band back together. They can also order additional links if needed. you can find a local retailer on

Jan 07, 2009 | Watches

1 Answer

Purchased fossil ladies watch am4183 at Macy's, stainless steel band is too big, is this band adjustable, if so how.

Check the sides of watch band and you will see the pin ends. They are holding all links together. If there are arrows inside the watch band, they are pointing the way the pins must come out.
To shorten the band you have to:
Extract the pins.
Take link(s) off.
Join the rest of band together and drive pins back.

Jan 01, 2009 | Fossil JR8096 Wrist Watch

1 Answer

Stainless steel band won't snap into my watch

Stainless steel bracelet ends (so called wings) must be curved flush to the watch case.
Another way is to use curved spring lugs (pins).

Dec 12, 2008 | Philip Stein Teslar Large Gunmetal Watch

1 Answer

Link removal of stainless steel watch band

Actually, this seems to be the big end of the split pen. Take a pin and push into the opposite hole ontil the big end pops out, then use pliers to pull it out. It should be easy to put it back. There should be an arrow on the inside of the band to show where to push.

Sep 04, 2008 | Citizen Eco-Drive Modern Watch

3 Answers

Broken strap.

contact Cartier. Donald

May 20, 2007 | Cartier Santos W20056D6 Wrist Watch

Not finding what you are looking for?
Watches Logo

Related Topics:

937 people viewed this question

Ask a Question

Usually answered in minutes!

Top Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18419 Answers

Ansel Alberto
Ansel Alberto

Level 2 Expert

248 Answers


Level 3 Expert

77932 Answers

Are you a Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides