Question about Barebone Systems

1 Answer

I have changed and ink cartridge but dont know how to change settings as infomation still says low cartridge

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers
Re: I have changed and ink cartridge but dont know how to...

The settings dont normally need to be changed as the ink is autodetected.

Posted on Feb 19, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

I no longer have my manual, how do I change the ink cartridges for the HP Officejet 6300 all-in-one?

To replace the print cartridges
1. Make sure the HP All-in-One is on.
Caution If the HP All-in-One is off when you open the print cartridge door
to access the print cartridges, the HP All-in-One will not release the
cartridges for changing. You might damage the HP All-in-One if the print
cartridges are not docked safely on the right side when you try to remove
2. Open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
3. Wait until the print carriage is idle and silent, and then lightly press down on a
print cartridge to release it.
If you are replacing the tri-color print cartridge, remove the print cartridge from the
slot on the left.
If you are replacing the black or photo print cartridge, remove the print cartridge
from the slot on the right.
4. Pull the print cartridge toward you out of its slot.
5. If you are removing the black print cartridge in order to install the photo print
cartridge, store the black print cartridge in the print cartridge protector or an
airtight plastic container.
If you are removing the print cartridge because it is low or out of ink, recycle the
print cartridge. The HP Inkjet Supplies Recycling Program is available in many
countries/regions, and lets you recycle used print cartridges free of charge. For
more information, go to the following website:
6. Remove the new print cartridge from its packaging and, being careful to touch
only the black plastic, gently remove the plastic tape by using the pink pull tab.
7. Slide the new print cartridge forward into the empty slot. Then gently push on the
upper part of the print cartridge forward until it clicks into the socket.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black or photo print cartridge, slide it into the right slot.
8. Close the print cartridge door
9. If you installed a new print cartridge, the print cartridge alignment process begins.
10. Make sure you have plain paper loaded in the input tray, and then press OK.
11. The HP All-in-One aligns the print cartridges. Recycle or discard the print
cartridge alignment sheet.
12. Press OK.

Jul 17, 2011 | Barebone Systems

1 Answer

Hi I have just inserted a new HP ink cartridge 94 into my HP PSC 2350, as the ink was running low. I was printing photos, which keept printing with a red line throughout the picture. After inserting the...

Try opening the printer properties and cleaning the print heads (should probably be done each time a cartridge is changed), it uses some ink up but should clean the build up from running the previous cartridge dry and hopefully solve your printing problem.

Good luck.

Mar 29, 2008 | Barebone Systems

1 Answer


When was the last time you changed the black ink on the printer? If it's been a while then I would suggest you change it. If you recently have changed it then you can try pulling the cartridge out of the printer and giving it a small shake. Put the cartridge back in and run an alignment operation on the printer. You can do that through the printer utilities installed on your computer.

Mar 26, 2008 | Barebone Systems

1 Answer

We just attached the macbook to the hppsc 1350v all in one printer and new print cartridges. When attempting to print, message reads"color print cartridge not compatible with this printer". We know we have...


Just to confirm pls:
1. the new print cartridges are original HP inks;
2. you have remove the bright pink tape from the ink cartridges;
3. the black is on the right side and the color is on the left side.

You can try removing both cartridges and clean the gold colored contacts where the pink tape was. Pls do the same to the mate pins in the cartridge holder in the printer.

Try again. If this does not be corrective, you may need to change inks again.

Hope this be of help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Feb 02, 2008 | Barebone Systems

1 Answer

When the printer runs out of ink, the head moves accross as normal to let me change the ink, but while I am trying to change the ink cartridge, the head starts moving spontaneouly and jams with the ink...

Printers can do strange things, they are none the less mechanical in some respects. Whilst in operational mode, they can start up and resume a print job that has been spooling for hours ( usually due to network issues or overloads ) but getting back to your problem, i would suggest turning the unit off when the head is in the correct spot and insert the cartridge.

Additional info ( not required reading )
I have one theory is that most manufacturers are re-using older software drivers and updating where needed, and aren't getting away from the step by step type program enough. If a printer misses a step for whatever reason, it will continue to behave strangely until the unit has been put back in sync. Please someone tell me why is this so ? and if i am wrong, why does my printer fire up in the middle of the night, spit out 10 blank pages for no apparent reason ?

Jan 22, 2008 | Barebone Systems

Not finding what you are looking for?
Barebone Systems Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Barebone Systems Experts


Level 3 Expert

18258 Answers

john smith

Level 2 Expert

366 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Barebone System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides