Question about Miele Premier-Plus Built-in Dishwasher

Open Question

Miele Premier Dishwasher fault

Hi Experts
During both wash and rinse programmes
Salt lamp flashes during initial fill machine fills a little more then salt lamp flashes again followed by the Inlet/Outlet lamp lighting and the prorgramme sequence display extinguishing and machine stops.

The Inlet/Outlet lamps remain on and there is at least 10mm of water above the inside filter combination.

Upon resetting and running a new sequence the machine pumps out fine.
I have reloaded the salt container and checked the salt hardness settings
I have flushed out the inlet filter within the inlet pipe connection
I have cleaned out the inner filters and non return valve.

Help required please!
Regards
Ray Baker

Posted by on

  • Atom ant Jan 21, 2008

    I've solved it! The Salt container has a reed switch activated by an internal magnetic float that senses a low salt level when float is low. The chamber was clagged up and the reed switch was buzzing sending false messages to the dishwasher controller.

    I removed and cleaned the salt container and the float, replaced and refilled, all is now good, no salt lamp flashing anymore and cycle all good.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 641 Answers

SOURCE: dishwasher salt

Cooking salt contains ingredients that could damage your dishwasher. It could increase water hardness and they are likely to clog when wet. Suck out as much water as you can from the salt cup,enter there dishwasher salt and run your washer few empty cycles on the lowest temperature. Good luck

Posted on Aug 18, 2007

Ad
gwshaw71
  • 83 Answers

SOURCE: Miele G638 CS Plus - Salt PC light flashes and will not run

have you added salt to unit?If so then you have a water intake problem or unit is oversudsing.

Posted on Dec 08, 2007

gwshaw71
  • 83 Answers

SOURCE: Inlet/Outlet light flashing

check your overflow level switch wich is located behind front kickplate on right hand side

Posted on Feb 24, 2008

  • 1462 Answers

SOURCE: salt for DDW1805 Danby

yes it is - salt is used to regenerate the water softener in the dishwasher

Posted on Jul 12, 2008

SOURCE: MY MIELE G856 SC DISHWASHER

press the start/stop and hold for 6 seconds that should clear it.

Posted on Jul 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to check a miele novotronic anti syphon unit


During rinse, water usually flows through the softener dispenser. The cup fills up and a small siphon tube triggers a siphon action
which pulls the softener and water into the washer. This siphon tube is probably blocked with crud. See if you can pull a small cap like part out of the softener dispenser area. Clean both the inside of the cap and the hole under it. This will allow the water to flow into washer instead of flooding.

Jul 06, 2016 | Miele Novotronic Premier 500 Front Load...

1 Answer

Machine nolonger fills on certain programmes and during rinsing


Hi Dominic
what i mneed to identify is how old the condensor/ dryer is from my experience i would suggest here is the cost involved it would appear you may have a programme fault can you advise me if its a pcb

May 16, 2012 | Candy AQW130 Front Load Washer / Dryer

1 Answer

Fon the dishwasher


Hi, welcome to Fixya.

Based on the info you've provided, the dishwasher is indicating a error during the "fill" stage, hence the "F" being displayed on the Bosch machines.

Here's how to perform a test or diagnostic...

Make sure the power button is in the off position ( open & closing of the door will activate the "auto shut off" ).

Once certain it is "off" press and hold both the regular button and rinse & hold button, then turn the unit "on" while continuing to depress those 2 buttons. Initially, control module version # will display ( i.e. "20" = version "0" without jumper...not important for this ).

When the buttons are now released, the lights above them will flash. To start testing, press both the "regular wash" and "rinse & hold" a second time.

Let the test follow through, ( grab a coffee and observe, this will take a while )

When testing has ended, the display will show an error using codes as follows...
"0" = no error.
"1" = aqua sensor fault.
"2" = heating fault.
"4" = filling fault. and finally.
"8" = NTC ( temperature sensor ) fault.

The "F" code will not appear in test mode, only during wash. If you have a failed level switch for instance the test will display "4" and will continually fill and drain and test won't complete until you press the "on/off" button.

If the test complete's without and error or won't fill, replace the water valve. Original part Part # 425458 at "searspartsdirect.com", "apwagner.com" or #1105846 at "repairclinic.com" ( they use there own numbers ) or you can check locally by your model number & serial number.

Let me know if I can assist you further. Hope you found this helpful and if so please allow for a positive rating.

Thank you for choosing "fixya" and good luck.

macmarkus :)

Jul 07, 2010 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Hello. My Bosch dishwasher display letter F and do not start. What i can do? Gary.


Hello Gary, welcome to Fixya. Based on the info you've provided, the dishwasher is indicating a error during the "fill" stage, hence the "F" being displayed on the shu43 series machines. Here's how to perform a test or diagnostic. Make sure the power button is in the off position ( open & closing of the door will activate the "auto shut off" ). Once certain it is "off" press and hold both the regular button and rinse & hold button, then turn the unit "on" while continuing to depress those 2 buttons. Initially, control module version # will display ( i.e. "20" = version "0" without jumper...not important for this ). When the buttons are now released, the lights above them will flash. To start testing, press both the "regular wash" and "rinse & hold" a second time. Let the test follow through. Whentestimg has ended, the display will show an error using codes as follows. "0" = no error. "1" = aqua sensor fault. "2" = heating fault. "4" = filling fault. and finally, "8" = NTC ( temperature sensor ) fault. The "F" code will not appear in test mode, only during wash. If you have a failed level switch the test will display "4" and will continually fill and drain and test won't complete, until you press the "on/off" button. If the test complete's without and error or won't fill, replace the water valve. Part # 1105846 at "repairclinic.com" or you can check locally by your model number & serial number. Let me know if I can assist you further. Hope you found this helpful and if so please allow for a positive rating. Good luck. Macmarkus :)

Jun 05, 2010 | Bosch 24 in. SHU43 Built-in Dishwasher

3 Answers

I have a Miele W1918 washer which has worked perfectly for a decade. Now there is not enough water to fill the tub during the first 'rinse' phase of normal cycles or the 'separate rinse' cycle. The machine...


I have exactly the same problem. I am currently getting around the issue by letting the machine do the washing then at the end of that cycle do a manual rinse cycle.

Jun 04, 2010 | Miele Novotronic W1918A Front Load Washer

1 Answer

Whirlpool ADP 5966 Dishwasher using the complete salt load in 6 washes and coating all the dishes in salt that would not rinse off. I filled the salt and 6 washes later it was requiring a new load of...


Hello, we are sorry to hear that you are experiencing this problem with the Dishwasher. We would recommend having a certified technician out to diagnose the problem. If you would like further assistance you can send your name, phone number, address, model/serial numbers and the date on which you purchased the Dishwasher to Whirlpool_Reviews@Whirlpool.com. Thank you.

Apr 17, 2017 | Whirlpool 24 in. ADP5966 Free-standing...

2 Answers

Miele Washer problem Novotronic Premier


Main wash light flashing is a heating fault. You either have a faulty temp sensor (NTC) or the pressure chamber has blocked and the heater element has popped.

Oct 22, 2006 | Miele Novotronic Premier 500 Front Load...

Not finding what you are looking for?
Miele Premier-Plus Built-in Dishwasher Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Dishwashers Experts

mpservices

Level 2 Expert

128 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Are you a Miele Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...