Question about Lexmark E232 Laser Printer

2 Answers

Photoconductor led blinks constantly along with the attention light

Posted by on

  • Anonymous Feb 08, 2008

    After replacing the photoconductor kit both lights are still blinking and I am unable to print,

  • toner girl Apr 14, 2008

    I changed the drum in the E232, however the light is still on. Any suggestions? Is there a reset proceeder?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

You need to reset the Photoconductor counter this can be done when the printer has cycled as far as it can go open the door and hold the second button down until all the lights have cycled once then close the door and you should be set to print.

Good luck

Posted on May 12, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,003 Answers

You need to replace drum it has reached its useage limit

Posted on Jan 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix a problem of green power led continuously blinking in Hp compaq nc6320 laptop even when the battery is removed and the motherboard is outside the case?


HP Notebook PCs - Troubleshooting LED Blink Codes or ...

h20564.www2.hp.com/hpsc/doc/public/display?...na...

Hewlett?PackardHP Notebook PCs - Troubleshooting LED Blink Codes or Beep Codes During Startup or Boot ... HP Pavilion and Compaq Presario notebook computers built in 2009 or later use blinking LEDS to identify ... Press the power button to turn on the computer, and look for blinking LED lights on the keyboard. ... Continuous blink.Missing: green ‎nc6320

HP Notebook PCs - Computer Does Not Start and Emits an ...

support.hp.com/us-en/document/c01732674
This document pertains to HP and Compaq notebook computers. .... light next to thepower socket or the light on the AC power adapter and note its condition: off, blinking, or constantly on. ... Battery power LED off, and Caps Lock/Num Lock off.Missing: green ‎nc6320

HP 6735s won't boot, power LED blinks 7 times - HP ...


Feb 03, 2016 | HP Computers & Internet

1 Answer

Sony LCD TV Red LED light constantly blinking


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details of many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.

Dec 06, 2015 | Sony KLV-32S550A 32 inch Multi-System LCD...

1 Answer

The printer toner light is continuously flashing even after putting in a new cartridge


After installing a new cartridge and the blinking light is on Toner Low, it means that the photoconductor is almost full and should be replaced soon. Press and release the Continue button (green button) to clear the light sequence and continue processing the print job. If the light is still blinking, replace the photoconductor kit.

For further assistance, please call Lexmark Technical Support.

Jun 14, 2011 | Lexmark E260D - QTY 4 - LMB OFFER Laser...

1 Answer

2 buttons of the lexmarkE260D are glowing> the


The light is second to the right is Toner Low. If ! and toner low displays a flashing light it means that the photoconductor kit is full and must be replaced. The printer will not print any more pages until the photoconductor kit is replaced.


Press and release Continue button to print a photoconductor kit instruction page. If the light is still blinking, replace the photoconductor kit.

For further assistance, please call Lexmark Technical Support.

Apr 12, 2011 | Lexmark E260D - QTY 4 - LMB OFFER Laser...

2 Answers

I swapped Photoconductors from 2 other 1710's; no go. Reset?


Problem
Dell 1700 printer prints out a page announcing that “the photoconductor has reached its useable life and it needs to be replaced for a new one”. You replace the photoconductor for a new one and the error light is still blinking and the printer keeps on printing the above mentioned page.
Solution
Steps to Reset the Photoconductor:
  1. Power off printer
  2. Open the front cover.
  3. Press the continue button; while pressing the continue button power on the printer and wait (still pressing the continue button) until the error led is solid, then release the continue button.
  4. Close the front door, all light should be solid.
  5. Wait until POST finishes.
  6. Press the Cancel button 4 times slowly, the toner led should be solid.
  7. Press the Continue button until all lights go up and down, then release; the Toner Low led is solid.
  8. Power off printer and then back on.
  9. Press continue button once, print a test page.
  10. Check the information about the photoconductor in test page, it should display an OK status.

Note: if these steps don’t work for the first time repeat three times. If still the steps don’t work, the printer needs to be replaced for a new one.

Jun 26, 2009 | Dell 1700n Laser Printer

3 Answers

No connectivity; constant blinking LED lights "Receive" and "Send"


Or you didn't pay your subscription on time and the ISP disabled your cable modem to send user traffic over the cable network. When both Send and Receive lights are blinking that is a visual aid that the modem is working fine, but the ISP disabled its access to the network (unpaid bill, legal issues, etc.)

May 17, 2009 | Arris SURFboard SB5101 Cable Modem

2 Answers

Hp lj 2500 flashing yellow light


The yellow-print-cartridge
light is blinking, and the
printer stops printing.
 The print cartridge is
empty or missing.
 The printer cannot
detect the print
cartridge correctly.
1. Reinsert or replace the print cartridge.
2. If the print-cartridge light is still blinking but the
Attention light is not on, turn the printer off and
then back on.
3. If the problem persists, repeat the above steps
with yellow print cartridges until the error is
resolved.
4. If the problem persists, replace the printcartridge
E-label reader, which is located on the
pressure assembly of the print-cartridge
carousel.

Jan 09, 2009 | HP LaserJet 2500L Printer

1 Answer

Toner light still blinking orange after new toner installed. Rebooted printer, light still blinking.


It means you need to replace the photoconductor kit (the bit the toner fits into) reset information is supplied with the new photoconductor kit.

Oct 15, 2008 | Lexmark E232 Laser Printer

1 Answer

Attention Light Flashing


Unfortunately, HP didn't make this indicator very descriptive. Their product specification page for this printer states that the blinking Attention light, "indicates that the printer media input trays are empty, the print cartridge door is open, the print cartridge is missing, or other errors".

You've already changed the print cartridge and the light is still blinking, so you should take a look at the other conditions described such as an empty paper tray, open door, and so forth. You also will want to look for a paper jam or carriage jam. These are two very common errors that will result in a blinking Attention light.

HP.com does provide a web page that describes a specific problem associated with a blinking Attention light:

Job Stuck in Queue

See if any of these suggestions work out for you. If not, post back your results along with anything else that you've learned about the problem. Good luck.

Oct 08, 2008 | HP LaserJet 1020 Printer

Not finding what you are looking for?
Lexmark E232 Laser Printer Logo

Related Topics:

936 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Don  Farrell
Don Farrell

Level 3 Expert

1018 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...