Want a wiring diagram for my apx4241 to my sub

try this link. Wiring diagram for 2006 nissan pathfinder LE sub woofer spreaker Google...
or this link... Wiring diagram for 2006 nissan pathfinder amplifier Google Search ..
not sure if the links will help you out but have a look.

Go to this site: http://www.bbbind.com/technical.html A huge database of free wiring diagrams.

Click on TSB's and wiring diagrams. Next page, agree to end user license agreement. Next page, click on "Wiring Diagrams", then enter vehicle information in the drop down boxes. Under "system" choose "engine". Under sub-system, choose "fuel controls". Then, click on "search" and you will see 3 results. The last two are engine compartment lay-outs, the first one is the fuel controls wiring diagram. When you click on it, will see all the wiring for fuel controls. When you want to see another system or sub-system, just click on "return to search page".

The socket the umbilical plugs into, is connected directly to the speaker output terminals. Your HiFi amp just feeds through the mission sub. The sub looks at the speaker terminals for bass information present. Making whatever noise it see's fit. I use one of these for a PC setup. I run a speaker wire from just one of my 2 desktop speakers, to any set of speaker out terminals on the sub that I like. The sub watches all 6 sets anyway, and my 2.0 desktop will be mono bass. So just one speaker wire is all it takes.

Follow the link and use the first diagram which illustrates wiring the subs to 2.66 ohms http://www.the12volt.com/caraudio/woofer_configurations.asp~Q~3~I~42

Remember that that amp is one ohm stable so you will not be getting the most out of that amp with that subs set up. The subs will only see 650 to 850 watts total...so each sub will only see about 215 - 275 watts a piece. Find out what the RMS wattage of your subs are each an determine if the wattage I mentioned above meets those requirements.

Dark side has you running the subs in series, not parallel. Subs if 8 ohm= Sub 1/ + - ' ' Sub 2/ + - = 4 ohm load, if they are 4 ohm subs that wiring diagram will drop you down to 2 ohm's. Hope this helps anyone in the future.

you can find your wiring diagram here
http://www.crutchfield.com/S-lCf6ewrWNQM/learn/learningcenter/car/subwoofers_wiring.html

Select from the list shown which describes your amp and subs (ie 2 channel amp with 2 4ohm subs)

Hope this helps and please rate, thanks

they are so many ways to run a dvc sub, let me know what ohms the coils are, and i will give you the ultimate bass that will hurt your hearing.

You can check Both Crutchfield's learning center on subwoofer wiring diagrams and www.the12volt.com with their wiring diagrams. The crutchfield setup will be more informative for this type of problem. Just go one of the + to one of the - on each sub then wire the other plus's together between the subs as well as the minuses like between the subs and use the open plus and minus that u didn't just bridge. Then there should be just 2 wires a plus and a minus to the amp. Then follow the amp bridge wiring which should be found right above the speaker terminals it will be left plus to right minus or the other way around

Contact company the can send you diagrams or go to a stero stop they should be able to help because some shop have wire diagrams for best way to get the most thump in you r trunk.Make sure you know the ohms your subs is 1-2-4 ohms.Should say on the back of your sub and how many contacts are on in two or four.

The LEd wires need a wire run from the speaker to the Fuse block in your car. The small Red wire from the LED will be the one that hooks to Swtiched 12 Volts supply on the fuse block so that your Led Turns on when you turn the keyswitch on. The Black wire goes to ground, or to a metal part of your cars body, probably the same point where your Amp is Grounded.

The Octane R10 is a Single Voice Coil or SVC.
AMP+ to Sub+
Amp- to Sub -
Use 12 guage wire.