Question about Nokia 5500 Sport Cellular Phone

1 Answer

Replacing 5500 cover

Hi ya
I have a replacement cover for the 5500 sport can you tell me how to locate the 2 screws that retain the cover above the screen

Cheers
stuart

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 53 Answers

Hi Stew,

I Have found a internet site on how to change covers on moblie phones this is the link www.lovehopefaith.com/v70help.htm you can try it`s got drawings of all moblie phones and how to take them apart I hope this site is helpful to you.

Posted on Jan 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can you replace the lights behind the instrument panel? the entire right side of my dash is no longer lit up


Sure Can

Buy bulb number 161

Instrument Cluster Finish Panel

Removal and Installation

1. Remove three screws along the bottom of instrument panel steering column cover (04459). Pull on instrument panel steering column cover to unsnap the three clips across the top of the instrument panel steering column cover. Remove the lower instrument panel steering column cover.

1996fp.gif

2. Remove four screws retaining the steering column shrouds (3530) together and remove the steering column shrouds.

3. Remove the three screws retaining the bottom of the cluster instrument panel finish panel (044D70).

4. Remove two screws retaining the cluster instrument panel finish panel above the instrument cluster face.

5. Pull cluster instrument panel finish panel to unsnap one retaining clip above the LH A/C register (19893).

6. Pull cluster instrument panel finish panel to unsnap three retaining clips on the RH side vertical edge.

7. Pull cluster instrument panel finish panel away from instrument panel (04320) far enough to disconnect the wiring connector(s).

8. To install, reverse Removal procedure.

I've never done #2, and #1 refers to the panel below the steering column. To remove it completely, pull it towards the driver's seat. There may be retaining clasps on it also.

May 25, 2011 | 1996 Ford Thunderbird LX

1 Answer

I have to replace the blower motor in a 99 astro van. Can it come out from the hood side or through the dash side?


1.Remove the air cleaner . CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
2.Disconnect the negative battery cable.
3Remove the electrical connector.
4.Remove the coolant recovery and windshield washer fluid reservoir assembly.
5.Remove the screws that retain the acoustic cover. The acoustic cover is located in the blower motor area.
6.Cut the acoustic cover between the ribs. IMPORTANT: Retain this portion of the acoustic cover for reassembly.
7.Remove the cut piece of the acoustic cover from the blower motor.
8.Remove the cooling tube from the motor.
9.Remove the screws that retain the blower motor to the case.
10.Remove the blower motor from the vehicle.


Ensure that the following components have not been damaged or distorted:
The flange of the blower motor
The blower fan
Repair or replace any damaged or distorted components, as necessary.



INSTALLATION PROCEDURE
Install the blower motor to the case. NOTE: Refer to Fastener Notice in Service Precautions.
1.Install the screws that retain the blower motor to the case. Tighten Tighten the screws that retain the blower motor to 2 N.m (18 lb in) .
2.Install the cooling tube to the motor.
3.Install the screws that retain the acoustic cover to the case. Tighten Tighten the screws that retain the acoustic cover to the case to 2 N.m (18 lb in) .
4.Install the clips to the clip lands. The clips secure the acoustic covers together.
5.Install the coolant recovery and washer fluid reservoir assembly.
6.Install the electrical connectors. CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
7.Connect the negative battery cable. Ensure that the circuit operates properly.
8.Install the air cleaner.

Thank you for using Fixya and be safe

Oct 21, 2010 | 1999 Chevrolet Astro

1 Answer

Dropped LG VX 5500 in water. Screen no longer lights up. Can receive and make calls. But cannot see screen.


Hello,

When it fell in water, it entered the screen and damaged it that is why the screen is not lighting up.

The solution to that is to replace the screen, to get to the screen follow the process below:
Turn your phone over so the back is facing you. Remove the battery. Now remove the 4 screws,
These screws may be covered by some plastic covers. These simply peel off.
Next remove the 2 rubber stoppers & screws above the main screen,
Now remove the two screws below the main screen,
Run a fingernail along the join of the housing to unclip it,
The top of the phone should now be in two pieces,
Unclip the ribbon. This attaches like a plug and socket,
Now detach the top of the phone from the bottom. This involves a little force as it is a tight fit,
Double back the ribbon on itself so it is away from the LCD screen,
Use the screwdriver to lever the old screen out,
Replace the old screen with new and reverse the whole procedure for reassembly.

Take care and good luck

Oct 16, 2010 | LG VX5500 Cell Phone

1 Answer

Dishes on the top tray still come out dirty after washing


This is probably a clogged internal disposal screen. This is a relatively simple procedure that requires 2 tools. There is a screen behind the cutter in the built in disposal unit that gets clogged easily. You may want to order a new part before disassembly. To disassemble: You will need 2 sizes of torqs (star shaped) screw drivers and some patience in reassembly. Be sure to note how things are assembled before removing them. You do not need to unplug the unit to do this as you will be inside the unit and not around any exposed electrical components. Make sure the unit has been off for a while so that the heater element is cool. Remove the top rack by squeezing and sliding the plastic locks upward (on the ends of the rails) Then slide the rack out. Remove the bottom rack turn the center plastic retainer on top of the spray mast cclockwise (opposite most all other screws) and lift out main spray arm remove screw from back center water pipe (oblong flat 2 piece plastic unit on the back wall inside) and rotate it clockwise to release the tabs under the pump cover. Lift above a carefully move out of the way loosen and carefully remove 4 screws from the pump cover/ diverter/ screen unit and lift out exposing the top of the pump and motor housing (usually grey plastic) Locate the screw at the front left of the pump cover that holds down the disposal cover. remove the screw and note which groove the screen is in as well as the side of the screen the blade is on. Replace the blade/ screen unit or clean the old one (under a tap of warm water and with an old tooth brush) and reinstall it. Assembly is reverse of above. Note! Be sure locking tabs are under pump cover as before and you don?t drop the screw for the oblong water pipe!

Feb 12, 2010 | Kenmore Dishwashers

1 Answer

Dishwasher wont push water around inside tub correctly something is blocking water flow to pump i looked for filter could not find


The units diosposal screen is probably clogged.
This is a relatively simple procedure that requires 2 tools. There is a screen behind the cutter in the built in disposal unit that gets clogged easily. You may want to order a new part before disassembly.
To disassemble:
You will need 2 sizes of torqs (star shaped) screw drivers and some patience in reassembly. Be sure to note how things are assembled before removing them. You do not need to unplug the unit to do this as you will be inside the unit and not around any exposed electrical components. Make sure the unit has been off for a while so that the heater element is cool.
  1. Remove the top rack by squeezing and sliding the plastic locks upward (on the ends of the rails) Then slide the rack out.
  2. Remove the bottom rack
  3. turn the center plastic retainer on top of the spray mast cclockwise (opposite most all other screws) and lift out main spray arm
  4. remove screw from back center water pipe (oblong flat 2 piece plastic unit on the back wall inside) and rotate it clockwise to release the tabs under the pump cover. Lift above a carefully move out of the way
  5. loosen and carefully remove 4 screws from the pump cover/ diverter/ screen unit and lift out exposing the top of the pump and motor housing (usually grey plastic)
  6. Locate the screw at the front left of the pump cover that holds down the disposal cover. remove the screw and note which groove the screen is in as well as the side of the screen the blade is on.
  7. Replace the blade/ screen unit or clean the old one (under a tap of warm water and with an old tooth brush) and reinstall it.
  8. Assembly is reverse of above. Note! Be sure locking tabs are under pump cover as before and you don’t drop the screw for the oblong water pipe!

Feb 06, 2010 | Kenmore 24 in. 16032 Built-in Dishwasher

1 Answer

Olds Ciera 1996 turn signal/cruise/wiper replacement


hello, hope this helps ya out...
1. remove th steering wheel retaining nut and remove the steering wheel.
2. remove lock plate cover with a couple of screwdrivers
3. push in lock ring enough to remove ring retainers.
4. remove lock plate
5. take off the retaining screws to remove the turn signal lever.
6. loosen and remove screws ro the hazard switch(3 i think)
7. remove trim panel under the steering wheel and locate the wire harness connected to the switch.
8. remove retaining bracket nuts and bolts on steering column and lower the bracket.
9. then you are able to remove the wire harness and switch.(you may want to tie a string or wire so that you can feed the wires back thru easier when installing the new one)
Install is the reverse of this. Please rate my answer so I know if I was of any help to you, good luck!!

Dec 19, 2009 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

How to change air filters on 2007 Mercedes C230 Sport


I have '05, both should be similar:
1.Cabin air filter is located above battery on right side against firewall.
Release three latches, remove filter housing, slide old filter out (housing is flexible), insert new
one, reinstall housing.
2.Engine air filter is on the left side of the block (follow intake hose). Cover is retained with six screws
(six point star shape,I belive called Torox, bit/scredriver size 25). Loosen screws (don' t pull all the
way out of the cover) lift cover , and remove old filter. Insert new one, reinstall cover. DO NOT
OVERTORQUE SCREWS! Screw holes in plastic filter housing strip very easily.
Note: Intake hose is very flimsy, one on my car came apart and had to be replaced.

Mar 25, 2009 | 2007 Mercedes-Benz C230 Sedan

1 Answer

Code


hi ya could ya tell me what codes ya using at mo and what provider so can look code up for you as mine still hasnt gone down cheers

Jun 30, 2008 | StarTech.com StarView SV211K 2-port KVM...

2 Answers

Dell Inspiron 1000 Disassembly


The teardown information from rbrown67 was very accurate and easy to follow. It helped tremendously in tearing down my machine to replace the AC plug.

Mar 14, 2008 | Dell Inspiron 1000 Notebook

Not finding what you are looking for?
Nokia 5500 Sport Cellular Phone Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nokia Cell Phones Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

270rexton
270rexton

Level 3 Expert

782 Answers

Are you a Nokia Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...