Question about Mitsubishi WS-55513 55" Rear Projection HDTV

1 Answer

Mitsubishi WS 55809 Rear projection TV

The TV is completely dead. I have checked the fuse and it's O.K. I found the following possible fix on this site:

You will need the DM module repaired....requires replacing
four 1000mf 16v 105 degree capacitors with a bit higher
voltage = 25v or 35v.....if too tall, lay them over 90 degrees on
to board.....there are many entries concerning DM module
rebuild...........if you need further assist,let me know...T.


This may well be the fix for WS 55513, but not sure if it applies to the WS 55809 model. As a novice, I may need a little more guidance. Is their a picture or schematic that can be supplied showing me:
1. What the DM Module is?
2. Were these failed capacitors are located on the DM module board? Additionally, could I get a part number for these capacitor components?
Any assistance will be appreciated, than you gentlemen

Email is juanjimenez23@hotmail.com

A

Posted by on

  • Anonymous Mar 16, 2014

    replaced bad caps dm power supply 1000mf 16v

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 4,402 Answers

Http://www.chrisandnat.com/Projects/BlinkingTV/blink.htm
http://www.jeremyburns.com/Mitsubishi-Green-Blinking-Light-Fix.pdf
http://www.fixya.com/howto/h159332-mitsubishi_dm_board_repair
http://hdtvoice.com/voice/showthread.php?t=32186
replace DM

Picture of bad caps
http://www.auctioncreations.com/wd62525a.JPG

The DM board is the one with the digital connectors on the back panel. If you already have it appart, you may as well check the caps on all of the boards. The caps that go bad are typically Jamicon brand caps in 1000 uF and 330 uF values. There are also a couple of 3300 uF caps in the PS that cause problems.

Posted on Jan 24, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dark pic on screen, unable to correct with regular means.


Regardless, my answer stands. It needs repair by a qualified technician. Rates vary by area. Make telephone inquires.

Jan 09, 2010 | Mitsubishi WS-55809 55" Rear Projection...

1 Answer

My Mitsubishi HD 1080 Model WS-55809 - the colors are distored. The picture is like double vision. For example the menu words all have yellow & red shadows.


Ur convergence it dead.U know how to solders?Buy a convergence kit.These websites have the kit.Tv repair World.com,Tv repair kits.

Dec 12, 2009 | Mitsubishi WS-55809 55" Rear Projection...

2 Answers

Where is the STK393-110


This TV uses 2 STK392-570's.
You will not find any STK393-110 inside your TV.

Jul 25, 2009 | Mitsubishi WS-55809 55" Rear Projection...

2 Answers

TV power will not stay on.


Not worth to fix.Either power supply,sensor or convertion board are too costly for the part.Buy a new TV.
solutiondoct

Nov 12, 2008 | Mitsubishi WS-55809 55" Rear Projection...

1 Answer

Mitsubishi WS-55809 2-2 code


look on the center board where the ics are and check F9A04 and F9A05 pico fuses, if they are blown you will need to replace those two 5 Amp picos and the convergence Ics

Nov 09, 2008 | Mitsubishi WS-55809 55" Rear Projection...

2 Answers

Mitsubishi ws 55809


22 is short protect usually its the convergence Ics in that model that can short out. check fuses F9A04 and F9A05 if they are open its most likely the convergence ICs that need repslacing. If you need further assistance, please reply to this same post.

Jul 29, 2008 | Mitsubishi WS-55809 55" Rear Projection...

2 Answers

Mitsubishi tv model WS-55809


that happened to me and i just gently hit it on the top and it fixed itself

Jun 28, 2008 | Mitsubishi WS-55809 55" Rear Projection...

2 Answers

WS-55807 doesn't power on


1) Check all fuse devices in power supply

2)Pc board with transformer possibly defective.............T.

Nov 07, 2007 | Mitsubishi WS-55809 55" Rear Projection...

1 Answer

Mitsubishi WS-55809


1)Check for coolant leak from CRT onto signal board

2)Possible convergence problem ..................T.

Oct 26, 2007 | Mitsubishi WS-55809 55" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-55513 55" Rear Projection HDTV Logo

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1230 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...