Question about RCA D52W20 52" Rear Projection HDTV-Ready Television

1 Answer

Cant get scenium off stand by mode not manually ,remote useless

Red light to front of t von strange noise from back of tv,willnot do anything

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • RCA Master
  • 8,617 Answers
Re: cant get scenium off stand by mode not manually...

Is The nise a squealing. (bearing Noise) ? If so its probaly bad bearing in your color wheel

Posted on Jan 16, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

The red power light comes on but nothing else works on my hitachi 53FDX01B PROJECTION TV

silly question but have you tried turning it on with the remote. if a tv has been turned off by remote and then power goes, turning it on by the tv switch will put the tv back in stand-by mode and you need to use remote.

just a suggestion.

Dec 13, 2013 | Hitachi 53FDX01B 53" Rear Projection...

1 Answer

Tv will not come on, I keep trying the remote and it won't turn on. Tried to turn it on on the set and that did not work either. There is a blinking light that says stand by. Just can't do anything. Help!!

oy, vey..sounds like ye olde Sony is tremendously unhappy. Ok..follow these steps.

1. unplug the tv, and let it sit for 2 to 3 min to ensure that all the charge is gone from the set and circuit boards.

2. turn off remote, comletely

3. Try manual mode with the buttons on front of set.

Blinking light usually means that there's something amiss on control board inside.

Are you the kind that will do this yourself, and is unit under warranty, by chance?

Feb 16, 2008 | Projection Televisions

1 Answer

Tv will not power up

Press the TV button or ON/OFF button while remote is in TV mode and there's a source of power to the outlet or outlet strip.

Make sure the TV is plugged in.

You might have tried to turn on the TV during the lamp cool-down. Wait a few moments and the picture will appear.

Has the power light on the front of the TV been blinking for one minute? If so, the lamp may be dead. Refer to the Power indicator
is blinking or flashing section below for more information.

When you first plug your TV into an outlet, the Power indicator on the front panel will light and blink for approximately 30 seconds
and then go off during the initialization of the TV. This happens only when the TV is unplugged and plugged back in. The TV can
only be turned on after the Power indicator goes off.

Check the wall receptacle (or extension cord) to make sure it is "live" by plugging in something else, such as a lamp.

Something might be wrong with your remote control. Press the POWER button on the front of the TV. If the TV turns on, check the
remote control solutions on page 53.

Multiple TV Setup might be set to the wrong option. Press MENU/OK on the front panel. Select Setup Options, then Advanced
Options, then Multiple TV Setup. Choose TV (default).

Sep 26, 2013 | RCA Scenium M50WH187 50" HDTV

1 Answer

Tv not coming on just red light flashing on and

thomson scenium jw 611s not coming on just red light flashing on and off at front of tv

Jul 13, 2010 | RCA Scenium HD65W20 65" Rear Projection...

1 Answer

I need to unlock the parental controls on the tv and i dont have a remote. i bought the tv used and i cant watch it

Try getting a universal remote that is compatible with that tv. Always look on the back of the remote packaging and it will tell whats compatible

Jan 10, 2010 | RCA Scenium D40W20 40" Rear Projection...

1 Answer

It wont turn on its stuck on stand by any suggestions? when we do get the tv turned on we cant knock it off or it takes hours of fiddling with the remote standby button to get it back on the tv is a...

This sounds like the front panel assembly(FPA) switches are acting up. What happens with this model is the FPA switches start to conduct just as if someone was pressing the buttons. This in effect locks up the system control or causes it to do erratic things.
The way to determine if the FPA is bad is to remove it by unplugging from set. This requires front panel disasembly. Note:The remote will still work with the FPA removed so the set can be tested.
Let me know if you need more help or info.

Nov 05, 2009 | RCA Scenium D40W20 40" Rear Projection...

1 Answer

Sony TV KP-51HW40 solid red lights [timer/standby+stereo]

if the main board by chance got wet you will need to use a blow drier to try and dry it may already be beyond fixing if water goi into it

Aug 17, 2008 | Sony KP-51HW40 51" Rear Projection...

1 Answer

Green light flashing & no picture on Toshiba 40pw13p

There is problem with the lamp. It might need to be replaced. The lamp unit is on the bottom-left side of your TV. Loosen thumb screw (by hand) to take the the lamp unit door. Using a screwdriver, loosen two screws of the lamp unit and carefully pull the lamp unit out.
Put a new lamp in reverse order.

Jun 28, 2008 | Projection Televisions

Not finding what you are looking for?
RCA D52W20 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 2 Expert

397 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides