Question about TV Receivers & DVRs

1 Answer

Captive works trying to load new program to the my captive works does not load what's my problem

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 26 Answers
Re: captive works

Either you have a bad been or you need to reset your reciever. Or may have a bad reciever wich was cloned from another do a power reset and see if that clears it up.
Good luck hope it works
Please rate

Posted on Jan 15, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Has anyone got the new ntl cable tv key & how do i put it into a pace digi box?

if u have legal box with card and paying a subscription, it will automaticly load , if uy have a cloned box u will need to program the card your self, allso there r other things u have to do hope this helps

Sep 15, 2009 | TV Receivers & DVRs

1 Answer

Weird clicking noise, can't record

It sounds like the internal hard drive has failed especially if this happens when you try and record a program, this will be the clicking sound that you can hear.
If the unit is fine until you try and record the i am in no doubt that it is the hard drive and it needs to be replaced.
Most new recorders have three and half inch IDE/ATA hard drives in them but it is a good idea to check first before you commit to purchasing a new one.


Aug 03, 2009 | TV Receivers & DVRs

3 Answers

Remote will not work

you would need to contact directv at 800-531-5000 and if programming it did not work, and setting it to default did not work, you may need a new remote. remote will cost about $15 unless you have the protection plan then it should be free depending on some circumstances.

Mar 31, 2009 | RCA DRD430RG DirecTV DTV Receiver

1 Answer

Dish Network "Blue" Smart Card upgrade... Now get only "015"

The solution is usually a simple one and that has been suggested already but I will ask you to try one thing first. Remove the new smartcard and do not put one in. If the receiver still displays a picture and yoou can get to menu 611 run a check switch. After this is performed cancel out of the screens and re insert the new smartcard. Once the system comes back up perform the same steps as you did before with the smart card removed. If this fails you can try the solution they offered which was to update the sofware. There is no reason your software should be outdated if you were using this receiver before the new smartcard but try anyway as it may SOMEHOW work. Using the remote turn the receiver itself off. Allow the receiver sometime to turn itself back on-this could take awhile so plan this when you leave for work or are going to be gone from the house for sometime so you do not get bored waiting for this to occur. If the receiver has not turned back on in 45 minutes or more then the receiver will either need replacing -which i suggest- or they will try to send you a new smartcard if you talk to Cust service. Tell them you want a service call to fix the receiver. While you have them on the phone verify your receiver number and the new smartcard number which is on the back of the card and ask them to send a hit to the receiver. If the receiver has not been associated with the new smartcard or if the smartcard was not loaded with all of your programmming this should fix the issue. Thanks for using Fix Ya.

Feb 22, 2009 | DISH Network 322 DTV Receiver

1 Answer

Directv receiver not able to load up

unplug the satellite cables from the dvr and restart it. it may or may load. if it does u can watch pre-recorded programs that are still on the hard drive

Dec 27, 2008 | Directv Plus DVR DTV Receiver / 100-Hours...

1 Answer

DISH 311 receiver will not load Program GUide Info

this is a softwar issue which should be fixed, are you in AK????

Aug 16, 2008 | DISH Network 311 DTV Receiver

1 Answer

Pansat 2700a Receiver

If you loaded a new program, make sure you check your DiSeqc switch settings if you are using one. Also make sure your dish is align properly. Try to do a blind scan to see if you pick up anything that is available from the satellite.
If nothing works, I would suggest to check C13 and C14 for bulging conditions, if they are defective; you will need to change them.
Good Luck.

Feb 29, 2008 | Universal Remote Control 2700A DTV...

1 Answer

Satellite receiver

It looks like you will have to load the factory bin 3 times using the NULL cable and not the USB pendrive.
Good Luck.

Jan 22, 2008 | RCA DISH Network(r) 311 Satellite System

1 Answer

Cant reprogram my sat dish

If you haven't already, try running the program in Vista's compatibility mode for XP. This page has instructions on how to do that.

If you've already tried that, or if it doesn't work when you try it, the program may simply be incompatible with Vista; if that's the case, you'll have to wait until the program's author releases a Vista-compatible version.

Dec 08, 2007 | TV Receivers & DVRs

1 Answer

Dishnet 811 unpluged during downloadfrom satellite

yeah that is a software download, if it does not progress it may have an issue, those receivers are being discontinued, call dishnetwork and they will provide you with a replacement leased receiver and a new dish install to receive all current hd programming

Sep 04, 2007 | DISH Network 811 HD DTV Receiver

Not finding what you are looking for?
TV Receivers & DVRs Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top TV Receivers & DVRs Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66518 Answers


Level 3 Expert

18258 Answers

Are you a TV Receiver and DVR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides