Question about Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool dishwasher green clean light is blinking and won't run any other mode. tried shutting electric off to the washer for 5 min. no change.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 447 Answers
Re: whirlpool dishwasher

Is it blikning 7 times and then repeating??? If so its a water heating fault. look in my solved solutions for more info on how to clear this fault.

Posted on Jan 15, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Whirlpool quiet partnerIII accusense light blinking constanly. cannot start

Try shutting the power/breaker for 5 min. Also toggle heated dry / energy saver buttons three times to reset eoc

Oct 30, 2013 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Clean light blinks on whirlpool dishwasher won't run

When the light flashes 7 times it means there is/was a problem with the hot water, including a bad heater element. Flip the breaker for a minute and hopefully that will clear the error; otherwise, here's a website that will take you through resetting it.

Apr 04, 2013 | Dishwashers

1 Answer

I have a whirlpool adp6600 dishwasher. the green light just keeps flashing (i think it's 7 times in a row each sequence) and the cycle won't start. have tried turning it off at the wall, clean

Dishwasher is in fault mode hold start/pause button for a few seconds this will reset the unit run your cycle again if dishwasher faults again call you local service man.good luck

Aug 02, 2012 | Whirlpool Dishwashers

1 Answer

Our "Clean" light is flashing green continuous and

Try running a cleaning cycle with no dishes. If you have hard water, try adding a little CLR, or cleaning solution. Check the bottom of the washer for clogged bottom drains. Also check the manual if you have it. Sometimes holding down the button for almost a minute will reset the systems alert for cleaning. Unplug and let it set for a few minutes. Good luck

Feb 21, 2011 | Whirlpool 24 in. DU1055XTP Built-in...

1 Answer

Washer will not start

Does the dishwasher plug in under the sink or is it hard-wired? If it plugs in under the sink unplug it and let it stay that way for 5-10 mins and see if that changes anything. If it is hard-wired see if you can figure out which breaker it is on and turn it off for same amount of time. Let me know.


Jul 31, 2009 | Whirlpool 24 in. DU1100XTPS Built-in...

2 Answers

How do you reset the whirlpool gu2400 xtp83 dishwasher. the clean light is flashing. The unit will not start

Can be caused by detection of a heater circuit problem. You can reset by running the diagnostic cycle. To turn of the diagnostic cycle, press: HEATED DRY button, then NORMAL button, HEATED DRY button again, then NORMAL button. The cycle runsfor ~22 mins. When it completes, the blinking light should go out. You can then try running the dishwasher again. If the problem comes back, the heater element or Thermister may need to be replaced

Jul 29, 2009 | Whirlpool GU2455XTS Built-in Dishwasher

1 Answer

Power surge here and had the same problem

sounds like a bad door latch.the unit thinks the door is open

Jul 24, 2009 | Whirlpool Gold 24 in. Built-In Dishwasher...

2 Answers

My Whirlpool quiet wash plus 940 series is stuck on "lock out"

Same problem and I was about to call for service. Opened the dishwasher to get the model number and noticed a sticker stating to hold down the Heated Dry button for 5 seconds to clear the lock light. Worked for me!

Feb 14, 2009 | Whirlpool 24 in. DU1050SS Built-in...

20 Answers

Kenmore dishwasher wont start blinking clean light

today January 9, 2009...blinking clean light, kenmore dishwasher would not run,,,the solution on Fixya ..."keep hitting normal -heated wash-normal -heated wash buttons over and over...unlocked the blinking green light problem. Dishwasher is running as I type this....will post again when I see the results of another washing tomorrow. H.T. Las Vegas Nv

Jan 18, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

Clean light blinks

Raise the temperature of your water supply. To reset computer open door,within 3 seconds hit hi-temp scrub then energy saver then repeat this. Close door and latch, push cancell button.

Jun 10, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Whirlpool GU2400XTP Built-in Dishwasher Logo

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides