Question about Uniden TRU9480 Cordless Telephone

1 Answer

Cannot hear the ring

I cannot find how to set the ring volumn on my cordless phone Model. TRU 94803. I have the base unit and 2 other phones and all work fine except for one.
Can you help me?
Thank you,

Posted by on

1 Answer

Re: cannot hear the ring

Just press the UP arrow, on the circle pad in the center of the handset. Likewise, press the DOWN arrow on the circle pad to lower it.

Posted on Jan 14, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My att cellphone only rings 4 times before voicemail

If the problem is with an AT&T cellphone you will need to call them or go log in online to change that feature, however if it is with a Uniden Cordless Phone (the product this question is linked to) the directions below found in their manual should help:

Uniden Cordless Phone
From the base
1) Press [clock/menu] three times. The base displays the current number of rings (2, 4, 6, or TS for toll saver) and announces the setting.
2) Press [>>/select] or [<</select] until the desired ring time appears.
3) Press [set]. A confirmation tone sounds, and the answering machine announces the new ring time.

From the handset
1) Press the MENU soft key. Select the ANSW. SETUP menu, and then the RING TIME submenu.
2) Move the cursor to select a Ring Time (2 TIMES, 4 TIMES, 6 TIMES or TOLL SAVER).
3) Press the OK soft key. You will hear a confirmation tone.

Hope this is of help

May 05, 2014 | Uniden Cordless Phone

1 Answer

Increase number of rings

You can select the desired ringer patterns of the base unit and cordless

handsets. 4 patterns are available for each line. Your phone comes from

the factory set to pattern 1. Programming must be carried out

separately for the base unit and cordless handset(s).

Make sure that the base unit/cordless handset is in the standby mode.

Base Unit Handset

4 Enter the desired pattern using

the dialing buttons ((1) to (4)) for

each line. To move to another

line, press H or I.

• Each time you select a pattern, it


5 Press (ENTER).

• A beep sounds.

• To return to the standby mode,

press (EXIT).

1 Press (FUNCTION).

2 Press or until the arrow

points to "Ringer setting",

and press H.

3 Press or until the arrow

points to "Ringer pattern",

and press H.

• The current settings are displayed.

Ringer pattern

L1 L2 L3 L4
1 1 1 1

Feb 20, 2011 | Panasonic KX-TG4000B 4-LIne Multi-Handset...

1 Answer

How can I clear the previous registrations from the TRU 9485 base?

Use the following steps to reset the base to factory settings for all TRU models:

1. Disconnect the power from the base

2. hold down the following three (3) keys: [dnd] + [middle soft key] + [*]

3. While holding down the keys, plug in the base (hold the keys down until you hear a long beep).

According to Uniden Tech support, this is supposedly all it takes to reset the phone.

Aug 12, 2009 | Uniden TCX905 Cordless Accessory Handset...

1 Answer

GE 28851 base handset #1, will not save ringer tone or volumn I selected. Brand New.

As it turns out, the primary base handset did save the newer selected ring tone and volume level setting.

However, the base maintains its own ring tone and volume level setting from factory.

Therefore, the base will present its own settings along with the handset setting during an incoming call.

So, one has to lower the volume of the base (in non-talk mode). The base should display in window: LO.

Then, only the ring tone and volume level selected for handset will be presented during an incomiong call.

How did I do????


Jul 09, 2008 | Uniden Cordless Phone

3 Answers

No dial tone at all

if the non-cordless phones are ok, it sounds as if the cordless handsets are the only ones not working, have you charged the batteries on those handsets ok and are there any signs if life, eg lights or on-screen messages ? Are they switched off ?
If there are signs of life, check the level of charge, if dead completely, take it/them to the main unit and put on charge for about 10 hours, if they work for only a short time and you have had the phones for a few years, then you will need to replace the re-chargable cells as they don't last forever and they are not holding the charge.
Hope this has given you some clues.....

Jan 16, 2008 | Uniden TRU8885-2 Cordless Phone

2 Answers

Panasonic cordless phone with answering machine model number Kx-TG2632 2.4 gigga range I miss place the book and I need help to adjust the volumn thank-you

The message on crystal reads"no link to base. Move closer to base, try again". I put in a new battery in each phone and not sure if they are charging. i keep getting the same message. What is the problem and how do I solve it?

Dec 02, 2007 | Panasonic KX-TG2632W Phone

1 Answer

My uniden tru 9485-2

My phone won't charge on the base unit. It does charge on the other smaller base.

Oct 19, 2007 | Uniden TRU9485 Cordless Phone

Not finding what you are looking for?
Uniden TRU9480 Cordless Telephone Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Phones Experts


Level 3 Expert

93861 Answers

Dave Ellis

Level 2 Expert

84 Answers


Level 3 Expert

7983 Answers

Are you an Uniden Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides