Question about Televison & Video

2 Answers

Top and bottom of picture missing

Top of picture down 2" from top
(some lines in upper part of picture)
bottom of picture, up 1" from bottom

every thing else is OK. The picture that shows is not distorted.
There are no adjustments on the back of TV

Posted by on

Ad

2 Answers

Note: after contacting you, I found the vertical transister (LA78041) was burned in two. I would have a hard time rating your response, because I haven't fixed it. You may still be right, but let me get back with you later. I will give you somewhere between helpful and FixYa!

Posted on Jan 15, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 232 Answers

Farout, bad capacitors in the vertical circuit, you`ll have to get a tv tech out for that repair, lots of them in that circuit and the tech will need the service manual to find them, BMW Rider

Posted on Jan 14, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to line up timing marks on a 72 Chrysler Town and Country 400 timing chain


Their are 2 marks on the gears
1 on the upper 1 on the lower .line the dots up in the middle top down bottom up they line up it works .
unless you screwed with the distrubitor shaft allinment you should be fine

May 13, 2015 | Chrysler Cars & Trucks

1 Answer

Only have part of picture on phillips 50tv


Are you missing the top portion of the picture or the bottom portion of the picture? looking inside the TV will reveal two modules to the furthest left of the inside. These are the upper and lower Y buffer modules. Replace the top one if missing the top half of the picture or the bottom one if missing that segment. Usually you can find good used parts on Ebay. Or Shopjimmy.com.

PHILIPS 50PF9631D 37 BUFFER BOARDS LJ41 03883A LJ41 03882A

Apr 05, 2015 | Philips Televison & Video

1 Answer

Got the wires mixed up on the distributor cap on my honda accord 2.3 L


1,3,4,2 is the firing order. Look at distributor and picture an imaginary line in the center of it from top to bottom 1 is top left, 3 is top right, 4 is bottom right and 2 is bottom left. There are ony four possible combinations if you mix up the top and bottoms .Write down on a piece of paper how you set them up in the event you get it wrong you can try it a different way. I don't know whybut currently I can't get a picture of this to you .

May 06, 2010 | 2000 Honda Accord

3 Answers

Vacum and fuel line diagram needed


I have an 89 Katana and don't know where the two vacuum lines on the top of the carbs go

Mar 11, 2009 | 1989 Suzuki GSX 750 F (Katana)

2 Answers

Projection HDTV Pansonic 47" Curving blue and green colors on top and bottom of screen.


You will need to replace your two convergence I.C.s.They are two large IC mounted on a large aluminum heat sink.Replace both,look for any burned resistors near them,replace those if needed,and readjust your convergence. Good Luck

Let me know if you need any further help

Mar 29, 2008 | Panasonic PT-47WX42 47" Rear Projection...

1 Answer

Consistent, faded and streaking vertical lines across entire page, from top to bottom.


Toner issue getting to drum - use gen toner cart.

or Drum blade stuffed (lines are down page fro top to bottom- replace drum assy

Drum has been exposed to light faint or blank across copies repeated 4 times down page - replace drum assy

or upper fuser roller stuffed, down page, smudgy print -  replace fuser

LSU(laser) or boards rarely cause issues

Oct 25, 2007 | Samsung ML 2010 Laser Printer

1 Answer

Slightly slanted screen/picture


your main filter capacitor in power supply has gone defective.

just replace it .

every thing will be normal.

good luck.

 

Oct 17, 2007 | Toshiba 36AF43 36" TV

1 Answer

3 curved lines top & bottom/blurred picture


This indicates a convergence problem..convergence power supply probally.. however ive seen 2 other cuicits cause this ..

Sep 24, 2007 | RCA HD52W59 HDTV Projection Television

2 Answers

Tv help!


When you have the back off, look for the flyback (high voltage) transformer. This is the part that has the thick red wire protruding from its top which attaches to the top of the picture tube with a suction cup. On the flyback there are 2 controls, the bottom one is screen and the top one is focus. Turn the bottom control (screen) down (counterclockwise) until the white lines go away and the brightness looks normal. Then turn the top control (focus) until the picture is nice and sharp. If the F connector has been pulled out and the TV has RCA (red, white, yellow) jacks, use those jacks and set the TV to INPUT.

Aug 13, 2007 | Zenith A27A11D 27" TV

1 Answer

Partial screen picture


bad caps in the vertical section

Dec 14, 2006 | Quasar SP-2722 27" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75846 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

82322 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...