Question about Kyocera Mita KM-3035 All-In-One Laser Printer

4 Answers

Sytem error C6050

Nothing works on machine, has system error C6050

Posted by on

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 36 Answers
Re: Sytem error C6050

This Code means low fixing unit temperature. If the power goes off and on, or Suzy Sec. has a space heater on the same circuit, this could be a false code.
Enter the service mode by keying in the numbers "10871087", on the key pad. enter the number 906, press start, press "execute"on the touch panel. The machine will reboot.
If the code comes back, you either have a bad thermistor, thermostat, or heater lamp. I have only had to replace the thermistor. The Fuser comes in the maint. kit ,so I always have some old ones laying around.

Posted on Jan 18, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers
Re: Sytem error C6050

Fusing errors aren't reset with 906, you'll need to run sim 163

Posted on Feb 27, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer
Re: Sytem error C6050

I tried this, and mine is not rebooting. Any Ideas?

Posted on Aug 07, 2008

Re: Sytem error C6050

Who the f*** is Suzy Sec.???

Posted on Sep 30, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to fix system error c6050 on my km-3035

It is a fixing assembly error code. The thermistor doesn't detect heat. Kyocera you replace the fixing assembly. You may be able to reset.1087 1087 gets u into served mode go to reset and activate.power off and on.

Feb 02, 2015 | Kyocera Mita Km 3035, 4035, 5035 Fs9120dn,...

1 Answer

Kyocera C6050 error

C6050 Error
Abnormally low fusing unit thermistor temperature

SIM 163 Reset (only do this one SIM, by doing others you could cause your machine to no longer function. Also see note at bottom.

Entering Simulation Mode
1. Press the system menu/counter key.

2. Select Service setting using the up/down cursor keys.

3. While pressing the start key and the # key, press the enter key. (Maintenance mode is entered.)

4. Select Maintenance mode using the up/down cursor keys.

5. Press the enter key.Enter the maintenance item (163 Resetting fuser problem) number using the up/down keys.
6. Go to step 1 under method below.
Resetting the fusing problem data Description
Resets the detection of a service call code indicating a problem in the fusing section.
When a service call concerning the fusing section occurs, turn the power switch off and open the front cover.
Then, turn the power switch on and press the system menu/counter key to enter the maintenance mode.
To prevent accidents due to an abnormally high fusing temperature.

1. Press the enter key. A selection item appears.
2. Select Execute using the up/down cursor keys.
3. Press the enter key. The fusing problem data is initialized. (Four service calls, namely C6000, C6020,C6050, and C6400 are reset.)
Press the back key. The indication for selecting a maintenance item No. appears.

Note:Sometimes in order to do the reset when the machine is in an error state you need to open the top cover (like to replace the toner) and leave it open until you have performed the reset

Jul 03, 2014 | Kyocera Printers & Copiers

1 Answer


C6050 Abnormally low fuser unit thermistor temperature The fuser temperature remains below 90°C/194°F for 1 s. Poor contact in the thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Broken fuser thermistor wire. Measure the resistance. If it is ∞ ω, replace the fuser thermistor. Fuser thermistor installed incorrectly. Check and reinstall if necessary. Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat. Fuser heater M or S installed incorrectly. Check and reinstall if necessary. Broken fuser heater M or S wire. Check for continuity. If none, replace the fuser heater M or S. Code Contents Remarks Causes Check procedures/corrective measures

Apr 09, 2010 | Copystar CS-1620 Copier

1 Answer

Error Code C6050

First you must get into the service mode by keying in 10871087
The screen will start blinking - then key 163 and the screen should read cancel or execute -select execute
when it is complete turn unit off then back on and see if that worked, if not buy a new fuser unit. They cost around $150,00 to $200.00 depending on who you buy it from.

May 25, 2009 | Kyocera Mita KM-2050 Printer

1 Answer

DSm415pf Rex-Rotary

The photoconductor has nothing to do with the toner. Photoconductor unit (Drum) is on a 45,000 copy cycle, and comes on when the count is reached. You don't have to replace the drum until the copy quality deteriorates. The machine will continue to work

May 11, 2009 | Gestetner DSm415pf Digital Imaging Sytem

1 Answer

Error: Call Service Code: C6050

try to press code 10871087 then 163 and lastly press clear/stop button for a while.

Nov 17, 2008 | Copystar CS-1620 Copier

1 Answer

Cannon l120 laser fax shows sytem error E100 and alows nothing to be done to it.It has worked for a few months now. Help!!!!!!!!

According to the knowledgebase on Canon USAs web site, System Error Exxx may be corrected by removing all power (unplug) for ten seconds, then plugging it back in.

Jun 30, 2008 | Canon Printers & Copiers

3 Answers

Kyocera KM4035 Service Message C6050

the above is incorrect, Kyocera made a mistake by having a thermistor that physically touches the upper heat roller/belt.. it has worn the roller to a point where it throws up the error.. you will have to install a new fixing unit.

I have done over 25 warranty replacements regarding the 4050/5050/2525 etc.

Sep 14, 2007 | Printers & Copiers

Not finding what you are looking for?
Kyocera Mita KM-3035 All-In-One Laser Printer Logo

5,979 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Printers & Copiers Experts

NewYork kyocera HP...

Level 3 Expert

513 Answers

Henry Gertcher

Level 2 Expert

46 Answers

Kevin Cole

Level 1 Expert

45 Answers

Are you a Kyocera Mita Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides