Question about Norcent Technologies LM-762 17" Monitor

1 Answer

Monitor issue the monitor image is shaking up and down in direction, however when computer is starting up, the windows logo is fine until it finishes loading and goes to the desktop.that is when the shaking starts

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.


    An expert who has answered 20 questions.

  • Expert
  • 163 Answers
Re: monitor issue

Look to Caps on the inverter if its an LCD or flat pan. monitor.. Weve seen this be4..

Posted on Jan 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

This is the strangest thing I've ever seen. I have a Gateway FPD1975W TFT Monitor and its always worked great. The other day it went into a sleep mode via windows, and now it wont boot up the input...


Your monitor problem is causes by the power supply. What is happening is the power supply voltages are not stable, just enough to power the unit up. When you connect it to a video signal the power demands slightly increase and the power supply can't handle it. This is a very common problem with LCD after a few years of use. The issue with the power supply is the capacitors have started to fail. These parts are used to filter the output voltage and when they start to fail the outputs start rippling hence the problem you are having. Here is a link to a repair article that shows how to repair the Gateway FPD1975W monitor.

I hope this helps you get back going.


Sep 20, 2011 | Gateway FPD1975W 19" LCD Monitor

1 Answer

Dell inspiron 1100 bought used reinstalled xp and monitor had only 6 inch image adjusted resolution, it grew almost perfect one more adjustment now quickly shuts. down image Windows logo with start up...

You may have set the resolution/refresh higher than is possible for the laptop to produce, Try booting into safe mode (F8 on power up)
if you can, you can now reduce the resolution to the monitors default resolution.
If you have not already, pop over to the dell support site and download the right driver for your display

Jul 19, 2010 | Dell Computer Monitors

1 Answer

Hello I wonder if you can help. When we switch

Had a similar problem like this several times. Try choosing safe mode. Safe mode will load the required drivers. After safe mode finishes the loading process, restart your computer and choose to start windows normally. The problem you mention usually happens when the computer is turned off without using normal shut down procedures. Also happens when you have a sudden power outage.

Oct 24, 2009 | Computer Monitors

1 Answer

Image shakes

check frequency settings and make sure its set at 60 htz,that is if your not in Europe

Sep 30, 2009 | Samsung SyncMaster 551 15" CRT Monitor

1 Answer

Cant boot computer

did u saw the hdd led blinking during the windows logo ? if it is so, unplug any devices other than keyboard and mouse, wait for sometime to finish its activity and see if it is fine then. else using the XP installer CD, run a deep scan for the hdd, repair the window or re install it.

May 03, 2009 | Dell E172FP 17" LCD Flat Panel Monitor

1 Answer

Monitor keeps stating "monitor going to sleep" now awhile after booting up. The monitor works fine with other computers and the computer in questioning when in safe mode - yet if tried to boot normally,...

This is probably a video setting issue. In Safe Mode, Windows starts with low resolution and color settings, so the monitor can display them. But when it tries to start normally, Windows is using a video setting the monitor can't handle.

Start the computer and press the F8 key three or four times when the manufacturer's logo screen appears. This should get you to the Windows startup menu screen, and you can pick the option of starting in VGA mode. This will start Windows with video settings any monitor can handle.

Once you have Windows up and running, make sure the video card and monitor types are properly set up. It would also be a good idea to download and install the latest drivers for your video card. You can usually find them at the manufacturer's website.

Feb 01, 2009 | Compaq FS7600 17" Flat Glass Monitor

1 Answer

Acer LCD Monitor only displays "acer" logo

You are correct, it could be a power surge that has caused it.

Try this..
Unplug the monitor from the wall.
Remove all the video connections at the monitor end.
Wait 10 minutes then plug the monitor back into the wall (do not connect the video leads)

Turn it on and see if it goes past the ACER logo now. If so, replace the video cables and try the computer.
If not, then one of these will apply and a tech will be required..
  1. The internal bios has been corrupted.
  2. The power supply inside the monitor may have issues preventing the video board from starting correctly. This could be as simple as a few failing capacitors.
Number 2 is the most likely cause with an Acer monitor though. Any local tech will be able to correct it fairly cheaply, but phone around for quotes..they can vary a lot.

Jun 03, 2008 | Acer X193W LCD Monitor

1 Answer

My VX924 Green Led Blinks until fully booted to windows

ok if what im understanding is you tried on another computer and it worked great
the monitor is not your problem the problem lies with your video card
the video card could be outdated
the video card could need updated software
the video is haveing a conflict with another IrQ on *********** board this is common in computers haveing conflicts
now if your not use to computers i would suggest to take it down to nears computer tech. store and have them set your IrQ for you this can get confusing
ask them if they can show you a walk threw on how to set the IrQ incase this happens again say if you do a restore on your comp i know you dont want to pay for it again to have them fix it
or you can call "GeekSquad" they can come to your home and fix it for you and show you a walk threw this might be better for u
i hope this helped you alot

May 25, 2008 | ViewSonic VX924 19" LCD Monitor

1 Answer

On Pwr up logo appears then LCD returns to stanby Black screen

I will assume the monitor is staying on during the boot process all the way until Windows loads.
If that is the case, then...
  • Start the computer
  • wait until the initial bios/logo screens for your motherboard go away.
  • Press F8 to get the Windows recovery boot menu
  • If you see the Windows Logo you would normally see then press rest and try again.
  • In the recovery screen, select SAFE MODE
  • Boot into Windows and uninstall your video card.
  • Reboot the computer the normal way through the start menu.
  • When your PC starts back up it should then reinstall the video card, and set itself automatically back to 60khz as default.
Let me know how you go =)

Jan 20, 2008 | BenQ FP71E 17" LCD Monitor

2 Answers

Monitor flickering and adjustment buttons locked

If the refresh rate is not properly set the monitor may have a wavy or an appearance that lines are going down ... This may also cause a flickering affect.
Distorted or skewed image on monitor. Issue: Distorted or skewed image on monitor.
Cause: This issue can occur from any of the below possibilities.
  1. Windows issue.
  2. Loose or defective cable.
  3. Refresh rate issue
  4. Interference.
  5. Bad monitor.
Solution: Windows Issue If your monitor has a proper display until it gets into Windows 3.x, Windows 95, Windows 98, Windows NT, Windows 2000, Windows ME, or Windows XP please see document CH000121 for software or setting related issues.
Loose or defective cable You may receive a distorted image when the cable is loose or defective. Disconnect the video cable going from the back of the computer and verify that no pins are bent, burnt or broken. Once verified re-connect the monitor cable.
Refresh rate issue If the refresh rate is not properly set the monitor may have a wavy or an appearance that lines are going down or across the monitor slowly or fast. This may also cause a flickering affect. Additional information about how to change the refresh rate can be found on document CH000558.
Interference A distorted image can be caused by magnetic or other types of interference. Verify no speakers, fans or other magnetic devices are close to the monitor.
Bad Monitor If the above possibilities have been checked it is likely that the monitor is bad. To verify this it is recommended that the monitor be temporarily disconnected and then connected to another computer. This can be a friends computer, a work computer, and/or a computer at a service center. You can also help verify a defective monitor by connecting another monitor to your computer. Note: Connecting your possibly defective monitor to another computer will in no way harm the other computer.

Good Luck/Please dont for get to Rate.Thank You.

Jan 17, 2008 | Samsung SyncMaster 940N Flat panel Monitor

Not finding what you are looking for?
Norcent Technologies LM-762 17" Monitor Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Norcent Technologies Computer Monitors Experts

Carl Glas
Carl Glas

Level 2 Expert

283 Answers

Ted Rishel

Level 1 Expert

5 Answers


Level 3 Expert

3018 Answers

Are you a Norcent Technologies Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides