Question about Protron 7" PORTABLE DVD

Open Question

My remote on 10.2 inch dvd tv/fm tuner does not work

I have protron 10.2 inch tv/ fm tuner , my remote  control do not work i have change the batery, what should i do is there a store i can take it to , and also my antenna broke  what should i do 
thank you patrick sajous

Posted by on

4 Suggested Answers

  • 1 Answer

SOURCE: Remote Control code for DVD Protron PD-800

There is no solution-it has no code-I contacted the manufacturer-it stinks!

Posted on Jan 22, 2008

  • 85 Answers

SOURCE: connecting protron dvd to dish TV

I hope you have at least 2 sets of RCA jacks for (1) the Dish receiver and (2) the DVD player. Run 2 sets of R/W/Y cables to the TV. Done. Or use S-video for a better picture instead of yellow.
If you only have one composite input on TV (possible) then either buy a 2-way or more switch for the composite signal (R=right sound W=left Y=composite or S-video instead of composite) or you can instead pass the signal through the DVD recorder on the RCAs but the DVD will be on whenever anything is on. I assume you do not have a Dish 111 with only RF output but the same could be done for just the wimpy RF, just different switch. So there will be 3 RCA cables from Dish to a recorder and 3 then to the TV. Since you do not have a recorder, then go back to the switch or find another TV input.
Ten years, hum, you may not have had composite/S-video inputs and would have to use RF only--you did not say what TV was.

Posted on Jul 19, 2009

  • 15935 Answers

SOURCE: I mistakenly purchased a Protron

You will need a universtal remote that seeks for the correct signal.
When you press the power button - it goes through all possibilities until it goes off.

Or purchase an original remote replacement HERE.
An original remote will give you all the functions available - whereas a universal will only give you the basic functions.

Please accept this answer to remove it from the work queue.

Thanks for using FixYa!!

Posted on Jul 23, 2009

  • 286 Answers

SOURCE: Where do I find codes for Protron DVD recorder

I hope that you have found the codes by now, but if not, here are the codes we have, and also the steps to program that remote.

1. Hold down the clear AUX button until all lights light up at the top of the remote
2. Punch in a 3 digit code (provided below)
3. Press the # (POUND) button
4. Try powering the DVD on/off, and the volume. If one or more of these functions do not work, start over from step 1 with a different code

685 is the only code we have for this brand.

Becki Barned
DISH Network Customer Service

Posted on Feb 02, 2011

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


1 Points

Related Questions:

1 Answer

Protron dvd remote control + player question


Jun 02, 2013 | DVD & Blu-Ray Players

1 Answer

I cannot get the Sony DVD remote control to work, and I cannot make a code work for the DirecTV controller to work the sony BDP-S301. Is there a code available for the DirecTV controller? Thanks.

direct tv only works with HDMI leads connected and to test remote use a camera on phone and point remote in it you will see light flash when press button if no light then change bateries

Nov 29, 2009 | Sony BDP-S301 Player

1 Answer

Remote will not control DVD/VHS

Tries change with new bateries,clean the The IR infered in the DVD/VHS combo unit,and the remote.

Aug 16, 2009 | Panasonic DMR-ES35VS

1 Answer

How to open and operate protron pdv 768

searched the web (google) and found a site that had the item for sale with pictures of it opened. once you see it open you can tell how to open it. inside are similar controls to a TV remote/dvd remote. rest was simple! thanks for your help though :) -r-

Dec 27, 2008 | DVD & Blu-Ray Players

1 Answer

Change region code as not region free

Turn on unit and put into TV/Tuner Mode
Press “Eject” button and confirm tray is out.
Press “repeat” button 3 times on remote
Press “0” button to make Region Free
When you see “OK” on screen, press enter or repeat on remote
Turn unit off
When you turn unit back on, it should be set for “Region Free”

Jul 29, 2008 | Protron PD-DVR100 DVD Recorder

1 Answer

Have a philips tv and a home theatre system but the remote off the surround system just changes the tv settings. Its kind of frustrating when I want to watch a dvd! Do I have to assign a freq?

When you press a function key on the remote control, not only does it change the function on the system (eg DISC, TUNER, TV etc) but it also changes the function on the remote.

However, if you change the function or source on the system, then only the system changes.

It sounds like you have changed the function on the system to DVD, but the remote is still set to TV. When in TV mode the remote will send Philips TV codes.

Press the DVD or DISC button on the remote.

May 10, 2008 | DVD & Blu-Ray Players

1 Answer

Loose remote control

Contact Protron directly at 1-888-257-8899.
They should be able to help you with a replacement remote control

Dec 12, 2007 | Protron TPL-C01

4 Answers

Remote Control code for DVD Protron PD-800

The code I used and it seems to work is 0194, but while trying to program my receiver, It changed some setting and the picture keeps looping over and over on the screen, and I can't get it to stop, I even made it worse while messing with the settings....

May 14, 2007 | Protron PD-800 DVD Player

1 Answer

Battery problems

hi , do you mean that your dvd player was working god b4 getting the batery back charged or you changed it completly solving your problem should depend on what your batery back state if it is new should be charged first time for 12 hours trty to power the dvd by a transformer if it get ok then you have a deffect batteries please don't forget to rate and remember i am here just for help thx

May 08, 2007 | Protron PDV-228 Portable DVD Player

5 Answers

Picture problems

Scrolling/black-and-white/"out of tracking" display on a DVD player is generally caused by the DVD player being switched into Progressive Scan mode on a TV not capable of viewing that content. Scan the remote for a button labeled Progressive, I/P, P.Scan, or anything similar. Scan the user manual for information on resetting this also. If the manual and remote come up dry, call Protron and see if there's a key combo you can hold to reset that. Often, holding Play for 5-10 seconds will reset to standard (Interlaced) mode, or holding Stop while turning the unit on. Sometimes, holding Display on the remote for a few seconds will also switch this setting. Good luck.

Jul 11, 2006 | Protron PD-800 DVD Player

Not finding what you are looking for?
DVD & Blu-Ray Players Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Protron DVD & Blu-Ray Players Experts

The Knight
The Knight

Level 3 Expert

66413 Answers

Jonathon summesfield

Level 2 Expert

284 Answers


Level 3 Expert

6993 Answers

Are you a Protron DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides