Question about Amplifiers & Preamps

1 Answer

Onkyo tx904 Hi gentlemen, my remote speaker switch seems to be malfunctioning, I am no longer getting any sound across my re,ote speakers; checked connects, an all the obvious stuff. Is there a way to bypass switch? Tanks Shannon

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 107 Answers
Re: onkyo tx904

I think it does really happen that way on some things like that , maybe its the controling IC or a busted resistor inside your amp. and check your speakers too. maybe they are shorting inside that makes your amp malfunction. try too open it or its up to you.

Posted on Jan 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Onkyo M-282

check your amplifier output speaker impedance requirements..
example: 8 a speaker 8 ohms in parallel or series connection..
check the impedance using ohmeter must reach the required impedance..

use 1 cell battery to check if you speakers are in-phase...if one speaker did not ..reverse connection and check again give the good sound...hope you understand my english..:)

May 24, 2010 | Onkyo M-282 2-Channel Amplifier

1 Answer

I have an ONKYO TX-SV717Pro amp. recently I lost

It could be that you lost the power supply to the surround amp IC or the Ic is defective. It should be mounted on a circuit board attached to the heatsink. Look for poor solder connections first. I don't recall the specifics of this model, but the surround amp IC should be easily located.

Update this with your progress and I'll try to locate the service manual in the meantime.


Oct 22, 2009 | Onkyo M-282 2-Channel Amplifier

1 Answer

Onkyo TX-SR576 7.1 Rear Channels problem

Have the same amp and speakers, had some trouble getting the imput signals sorted from the HDMI input as im using a PC with HDMI output from the mother board and Windows Media Centre. havent tryed using the mic set up yet.

Did you resolve the issue? have you tried the 7.1 outputs

Jun 21, 2009 | Onkyo Amplifiers & Preamps

1 Answer

Connect cheap speakers to a new amplifier

You need proper speakers,pc speakers uise mini headphone jacks,wrong termination for an av amp

Dec 21, 2008 | Plantronics MX10 Computer Speakers Use w/...

1 Answer

Speaker distortion on high end

Sounds like classic dry joint on speaker terminal ROTELS are well known for it,if you can use a soldering iron or know someone who can resolder the pins where these terminals are connected,always make sure amp is unplugged from wall socket before ...

Dec 18, 2008 | Onkyo M-282 2-Channel Amplifier

1 Answer

No sound

Use your speaker to another unit if it working, if not then the problem is your speaker,other checking technic use a multitester set it to X1 check the lead connection of the speaker if has a resistance 4ohms or 8.

hope this may help;



Aug 17, 2008 | Onkyo Amplifiers & Preamps

1 Answer

Onkyo 9555 protection circuit

Make shure your speaker wiring is solid hookup to amp and spekers (NO CROSSED WIRING). Also make shure speakers are not wired in parallel or the speaker impeadance will be to low and amp will kick out.Turn speakers off then hook up headphones and crank up volume then see if amp kicks out.If it does you have an internal overload and needs serviced. If it playes ok then you must have speaker problems or wiring.

Mar 26, 2008 | Amplifiers & Preamps

1 Answer

Onkyo a-rv410 amplifier output problem

Hi pm, Hard to make an assertion without firing it up yourself. It may be that be has faulty speakers, speakers out of phase, faulty earthing of line out from the source he tested it with.
Good chance that it is ok. Take advantage of his concerns, and buy it extra cheap. Good luck


Feb 26, 2008 | Amplifiers & Preamps

1 Answer

Don't know how to adjust volume on remote speakers

Can I ask you something? I have the same but the remote doesn't work, and I have no sound in the B speakers. I wonder if there's something that I have to do with the remote, or there's a problem with the receiver, Thanks.

Jan 16, 2008 | Onkyo M-282 2-Channel Amplifier

1 Answer

No sound through the speakers...

It may be the PS3
you have to select Optical Out 5.1 etc first.
That PS3 is not user friendly at all.

Colin Graham.

Oct 22, 2007 | Amplifiers & Preamps

Not finding what you are looking for?
Amplifiers & Preamps Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amplifiers & Preamps Experts


Level 3 Expert

4518 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

66444 Answers

Are you an Amplifier and Preamp Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides