Question about ASUS P4GE-V Motherboard

1 Answer

Front Panel Audio

I own the Aus P4GE-V motherboard, i lookd at the diagram and tried hooking up my frount panel audio wires to the pins wich it said to, but there was also to jumpers i had to pull off, but when i pulled them off and hookd up the conectors no audio will work at all now, the frount panel audio is on a tsunami computer case, the single wired conectors for frount audio are *Mic In *Mic Out *EARO-R *EARO-L *Reserved *AGAND, can you tell me how to hook it up so i can have rear and frount audio

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

I don't believe that this motherboard supports simultaneous front and rear audio. That's the purpose of the jumpers; to route audio to the back panel when on and to the front panel when the front panel connectors are connected,

Posted on Jan 13, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am looking for a wiring diagram for the mic in, mic power and mic ground on a gigabyte motherboard 8vm533m-rz


25126305-cyh1nhlz3nmhmciytcwjnjrb-4-0.jpg


"The front panel audio header on an Intel® Desktop Board lets you connect to a front panel audio module built into a system chassis. This document describes the header pin-out configuration for connecting a chassis with Intel® High Definition Audio (HD Audio) or AC'97 audio.
Note HD Audio headers are pin-compatible with AC'97 chassis and connectors. "

-intel Desktop Boards Front Panel Audio Header Pinouts

Sep 22, 2014 | Computers & Internet

1 Answer

Need circuit diagram for HP m8100 GC673AA


HP Support > Pavilion Media Center M8100n Desktop PC > Main Support page,

http://h10025.www1.hp.com/ewfrf/wc/product?product=3440614&lc=en&cc=us&dlc=en&lang=en&cc=us

Product information > Product specifications > Motherboard Specifications, MCP61PM-HM (Nettle2 {HP name} ),

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01077676&tmp_task=prodinfoCategory&cc=us&dlc=en&lang=en&lc=en&product=3440614

The front of your computer is the Front Panel.
The area of contact pins on the motherboard, that the Main wires connect to, is the Front Panel header.
(Power On switch, Power On LED, HarDDrive activity LED, etc)

The Front Panel header is Black, rectangular in shape, and is situated in a vertical position; located in the Bottom Right corner of the motherboard. (Next to the mounting hole)

It is a standard 9-pin HP Front Panel header,

http://h30434.www3.hp.com/t5/Desktop-Hardware/Getting-a-new-case-i-need-Front-Panel-pinout/td-p/842897

Scroll down to the 9-pin Front Panel header photo, and pinout.

The 4-pin side is the EVEN side. Pins 2, 4, 6, and 8. There is NO Pin 10.
The 5-pin side is the ODD side. Pins 1, 3, 5, 7, and 9.

A) Pins 1 and 3 are for the HarDDrive activity LED. (Light Emitting Diode, so it is redundant to call it a light)

Pin 1 is for the Positive ( + ) wire.
IF the HDD LED is dim when the harddrive is active, (IN use), switch the wires around.

B) Pins 5 and 7 are for a Reset switch, IF a Reset switch is used.

C) Pin 9 is N/C. Not Connected. Reserved for factory use, and it is +5 Volts.

D) Pins 2 and 4 are for the Power On LED.
Pin 2 is for the Positive ( + ) wire.
If the PWR LED is dim when the computer is on, switch the wires around.

E) Pins 6 and 8 are for the Power On switch.

Scroll the HP Support Motherboard Specification page down. Click on the + sign next to Motherboard Layout.

Left to Right on bottom edge of motherboard, Internal Connectors;

AUDIO_1 is for the audio ports on the Front Panel.
ATX_IN is where the small audio cable from the optical drive plugs in.
(CD/DVD drive)
IF TWO optical drives are used; the Main, or Primary optical drive, is connected with the small audio cable. NOT the secondary optical drive.

HD_AUDIO also connects to audio ports in the Front Panel.
May be mistaken, but don't believe SPDIF_OUT header is used.
1394A1 header is for the Firewire ports in the Front Panel (1394a)
USB 2 and USB 4 headers are for the Front Panel USB ports.
USB 1 and USB 3 should be for a Card Reader.

Need where the power cables go, and what they look like? Just post back in a Comment.

(Be SURE to FOLLOW Anti-Static Precautions)

Regards,
joecoolvette

[ Didn't think you actually wanted an actual circuit diagram. That is copyrighted by HP, and Elitegroup Computer Systems. (ECS)

Dec 03, 2012 | Computers & Internet

1 Answer

Hi ,, i have just fitted a intel d845gvsrb in my pc but i am not sure where the tower speaker wire , reset sw , power sw , power led , h h d led and the black single one go`s can you please help me ..


The Picture below shows you the locations of the places to put those wires are in relation to your motherboard. In yellow is the power switch and such. and the audio connection is in red.
avatar23454_9.jpg

The Pin layout for the power and other connector are as follows:
avatar23454_10.jpg

the layout for the audio header is as follows: avatar23454_8.jpg

To install the cable that connects a front panel audio solution to the front panel audio header, follow these steps:
  1. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord.
  2. Locate the front panel audio header (J8A1).
  3. Remove the three jumpers from the header (this disables the back panel audio connectors).
  4. Install a correctly keyed and shielded front panel audio cable.
  5. Connect the audio cable to the front panel audio solution.

To restore back panel operations follow these steps:
1. Remove the front panel audio cable. 2. Install a jumper on pins 5-6 (rear R channel). 3. Install a jumper on pins 9-10 (rear L channel). 4. Install a jumper on pins 1-2 (mic). 5. Replace the cover.

Apr 17, 2011 | Intel D845GVSR Motherboard

1 Answer

I want to know where the connection points are on the motherboard for the front mic and audio jacks. I have a epox ep-5pdaj motherboard. Will you send me a diagram please.


close to the back panel of the mainboard, below the back i/o connectors and 3.5mm audio jacks.
1b3231a.jpg


You need to remove the two jumpers from the pins, this is where you connect the front panel audio connector, if your case has each wire separate. then please look at this webpage http://www.intel.com/support/motherboards/desktop/sb/cs-015851.htm look at the part "For AC97 Front Panel Audio" PIN 1 should read MIC. If not, then scroll down, you are reading the wrong part of the page.

Aug 07, 2010 | EPoX EP-5PDAJ Motherboard

1 Answer

Hook up for the audio on the front panel


When you are looking at the motherboard with the CPU and memory slots on the right, the audio hookup is up on the edge of the motherboard on the left. It's the last set of pins in the upper left side of the motherboard. If you have an audio jack in the front of the machine, you should have an audio cable just hanging there somewhere that is not hooked up. Hook it to the audio connector that I described.

Jun 10, 2010 | Biostar K8M800 Micro AM2 VIA K8M800 uATX...

1 Answer

Green light indicator and front panel USB


it should be on your motherboard book diagram. if not try to read the motherboard type and model and post it here if you cannot find the manual it should be simple. often the front panel audio slot is formed with 8 pins 4 by 4 and it should be right bellow it written F_panel or F_audio

Dec 26, 2009 | Computers & Internet

1 Answer

I need a diagram that shows the pinout for front panel audio.


Could you be less specific as to what motherboard and front-panel, and why you couldn't download the manual from the maker if you pitched it out?

Then, to be sure, get a DVM with small probes, set it on continuity, and confirm the pinout.

Aug 24, 2009 | Computers & Internet

1 Answer

Abit an7 motherboard front panel wiring diagram needed :)


Front pannel audio is located left of the pci slots 
: : : . : : :   thats what it looks like         from left to right there are seven sets of pins 1234567. 
3 and 7 should be the pins you want for a standard front panel audio as far as i see in the manual ICEBOX  



















 

Mar 22, 2009 | Abit AN7 Motherboard

2 Answers

Ibm 8303-21g front audio pin configuration


Manual usually has diagrams and pin configuration for your system.
If you don't have the manual go to their web site and take a look.

Feb 06, 2009 | IBM Computers & Internet

Not finding what you are looking for?
ASUS P4GE-V Motherboard Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Alun Cox

Level 3 Expert

2678 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...