Question about iLO (2 GB) MP3 Player

1 Answer

The plug in for my headphones just works half the time and most not at all

I can plug my head phones in and only one side works and most of the time they don't at all. I have bought a many number of new ones and the problem wasn't them it was the plug in . what can be done to fix this problem.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Dont spend your money trade it i for a sony mp3 that is what i use 1gb is $25 2gb is $35

any problems wit that email me on 62992murra@gmail.com

Posted on Jan 14, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a cylinder head on 2001 Ford Expedition 4.6 L V8


Actually, rather than replace the head, you can fix the spark plug hole with a "Time-Sert":

http://www.timesert.com/

One thing they talk about on the site, "Ford spark plug blow-out? Repair kit part number 5553 Ford Triton spark plug kit will repair blown out spark plug's in Ford heads."
Here's the page for Ford's repair kits:

http://www.timesert.com/html/sparkplugford.html

I've used these for years, and they work great!
Much better than a Helicoil, as the Time-Sert retains full thread strength!

But....I would STILL recommend removing the head to do this repair, so as to avoid metal chips/shavings from falling into the cylinder, but you'll save the cost of a new head!

Sep 05, 2014 | Cars & Trucks

1 Answer

What is tork specs for 2004 883 sportster head bolts


The procedure for tightening the head screws is critical.

Start with bolt numbered one which for the front cylinder is the left side or spark plug side rear bolt then the left side or spark plug side front bolt which is the number 2 bolt then the rear right side bolt which is the number three bolt and then the front right side bolt which is the number four bolt AND tighten the head bolts in sequence from one to four in the following steps:


Tighten each bolt to 96-120 in-lbs, then tighten each bolt to 13-15 ft-lbs, then loosen all bolts, then tighten three stages to: first stage tighten each bolt to 96-120 in-lbs; second stage tighten each bolt to 13-15 ft-lbs. THEN mark each cylinder head and head bolt shoulder with a reference line and tighten each bolt an additional 85-95 degrees.


Start with bolt numbered one which for the rear cylinder is the left side or spark plug side front bolt then the left side or spark plug side rear bolt is number two then the front right side bolt is number three and then the rear right side bolt is number four AND tighten the head bolts in sequence from one to four in the above steps.

96-120 in-lbs = (11-14 newton meters)
13-15 ft-lbs = (18-20 newton meters)

May 23, 2014 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I have a 99 Jeep Cherokee limited and when I turn my lights on my tails don't work but when I apply the brakes the passenger side comes on. I replaced blubs and sockets.


Had a similar problem in mine. When I applied brakes while head lights were on, the the light would go off completely. There is a computer chip in the tail light assembly that tends to go bad causing the light to malfunction. I just bought a new tail light assembly from eBay and now it works perfectly. As easy as putting in a new bulb but you just have to unplug electric terminal from the light and plug in new light once received.

Oct 26, 2011 | 1999 Jeep Grand Cherokee

1 Answer

I bought new ink cartridges and when i try to print something it gives me a error number 5100


Cause: Head too hot, exceeds the threshold, usually the color Catridge
Solution:

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 26, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

The car keeps blowing head light on the passenger side the shop said it needs a new wiring harness but the head light is the only problem that I have any suggestions would be apprieciated


you can buy a new head light plug assembly at a parts store. this will require snipping and soldering the wires in the car to the new plug. also most often what has happened is that the ground wire connection from the old plug connector has corroded and is no longer giving you a good ground. so before i bought a new plug and cut the old one away and began the soldering work i would check, clean, and work on that ground connection a bit. you will have to solder the new plug wires as twisting them in a regular mechanical splice with a wire nut is going to cause flickering and dimming when corrosion builds up on the wires.

Jun 29, 2011 | 2004 Pontiac Grand Prix

1 Answer

My headphones have stopped working. I cannot hear sound from them at all, even though I haven't been using them much. It's model MDR-EX71SL and I bought them less than 9 months ago.


Have you tried them in another audio source. Head phone wires like to break at the strain relief of the main plug. Try moving the cord on the plug side of the phones. If it cuts in and out its time for a new set. Head phone wires are difficult to repair and it may be more trouble then its worth.

Oct 10, 2009 | Sony MDR-EX71SL Consumer Headphones

1 Answer

The printer won't recognise the printer cartridges. I tried replacing older cartridges with new ones and even this doesn't work. They are genuine epson cartridges and the same ones I have always bought.


Check chip connnector at ink tank and at head carriage. It's may be dirty. Check status monitor? what ink tank not recognized. Press ink light (1-4 times) depends on number ink tank not recognized, press 1 time again, carriage will move co replacement position, unplug and plug again all ink tank, press ink light 1 more.

Jun 29, 2009 | Epson Stylus C46 InkJet Printer

1 Answer

New proscan 32 lcd tv. Won't work with sony wireless headphone


Try using the PROSCAN website customer support, to find the answer to you questions.www.oncorpus.com. You will need some type of adaptor from th coax output to the input of you system. For the wireless problem you may need two adapators one from the tv to you receivers and a sound output to wireless adapator. You can call them at their customer support telephone number 1-888-977-6722. I hope this information helps you with your problems.

Mar 31, 2009 | Proscan 32LA30Q Television

1 Answer

Audio Problem


Mine does that too. I am not sure if it works with other things but I just bought new ones.

Jan 02, 2008 | SanDisk Sansa e260 MP3 Player

1 Answer

Brother printer mfc4420 c


If you don?t have proof of purchase (receipt) they typically will ask for the serial number, figure out the manufacturing date and use that as the start of your warranty. If that didn?t happen call back and explain your problem again, omitting the previous call. There is nothing dishonest about this; you probably got a lazy, incompetent or new phone representative and telling them someone else said no just gives them an easy way out. If you get the same response nicely ask for a supervisor. Explain that while you understand they are following instructions it seems unfair and you would like to talk to the supervisor. If you have a reasonable request and behave nicely you can usually get some satisfaction. If your printer was made over a year from the manufacturing date then you?re probably out of luck unless you purchased the printer from an on-line store. They can easily give you a print out of the purchase with the date it was bought. Good luck and please don?t forget to rate this posting.

Mar 14, 2007 | Brother MFC 4420C All-In-One InkJet...

Not finding what you are looking for?
iLO (2 GB) MP3 Player Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top iLO Audio Players & Recorders Experts

Mohamed Ismail
Mohamed Ismail

Level 3 Expert

462 Answers

Allen Benge

Level 1 Expert

3 Answers

Jon Piercy

Level 2 Expert

67 Answers

Are you an iLO Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...