Question about Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

2 Answers

Drill sometimes the drill dont work when i press the button until i shake it vigorously

Posted by on

  • Anonymous May 27, 2008

    WHEN I PUSH ON THE TRIGER MOST OF THE TIME IT DOES NOT WORK

  • jon perry May 16, 2009

    i have a dewalt dc920 xrp 18v drill and it doesnt work unless i shake it.ive changed the brushes and adjusted the battery connections.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Hi hope to help
sounds like you have a problem with your brushes they may just need replacing but do not strip the drill down to do this just take out the batery then take the 4 screws from the rear off the drill and take off the cover see if the brushes are worn it doesnt take a lot of wear to be worn.
You can take off the wire from each brush unit then use a small flat screwdriver to pop out the brush unit then replace you should be able to get the brushes from any dewalt stockest.
Hope that helps. Sean

Posted on Mar 04, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 313 Answers

I guess switch problem

Posted on May 28, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you clean a Stanley mug lid??


How to Clean Stainless Steel Coffee Mug Hunker

However from Stanley:

You'll need:
  • ¼ cup uncooked rice
  • 3oz distilled white vinegar
Instructions:
  1. Pour ¼ cup of uncooked rice into flask.
  2. Fill flask with 3oz of distilled white vinegar.
  3. Seal flask.
  4. Shake vigorously for 1 minute.
  5. Let sit for 5-10 minutes.*
  6. Shake vigorously again for 1-2 minutes.
  7. Empty flask. Bonus points for composting the rice.
  8. Rinse thoroughly with warm water.
  9. Leave open until dry.

How to properly clean your Stanley products

Jan 11, 2018 | Coffee Makers & Espresso Machines

1 Answer

My Ryobi PD750 impact drill just stopped working! Is there a safety button or something that could prevent it from working? Ive tried other plugs. Its fairly new.


The wires on the brushes sometimes shake loose , tool repair shop ,, or try it yourself ,, remember. Small parts ,, take pictures , tiny wires , may need to be soldered back in place ...

Jun 11, 2017 | Ryobi Drills

1 Answer

Faulty bosch hammer drill


a bad trigger switch; bosch sells a replacement part

Jul 24, 2010 | Bosch Drills

1 Answer

Uhh....... the blender mafuntioned when i plug in it blens even when i dont turn it on


Sounds to be a switch is stuck or button . Tap each button vigorously and turn each one on and off. Pressing another speed should cancel what ever button is stuck. Good Luck, Ned

Sep 27, 2009 | Sunbeam 4192 Work Top Blender

1 Answer

MY 92 CUTLASS AFTER 20 MINUTES STARTS SHAKING VIGOROUSLY THEN DIES AND WONT RESTART UNTIL IT COOLS DOWN 20 OR MORE MINUTES THEN STARTS RIGHT BACK UP


if a temp. light does not come on and the engine is not over heating I would look into the ignition components such as ignition module inside the distributor, sometimes when these components heat up they can cause this problem you described

Jul 03, 2009 | 1998 Oldsmobile Cutlass

1 Answer

Drill doesnt work unless shaken


It sounds like a bad cord, or a loose electrical connection inside the handle, or the switch.

Instead of shaking the drill, try wiggling the cord where it goes into the drill handle, then wiggle it where if plugs into the wall.

If this doesn't cause the drill to run, try pressing the switch repeatedly to see if that causes it to run. If that doesn't work, it's probably a connection inside the handle.

Try these procedures and please let me know the results. We'll take it from there.

thanks...

Charlie

May 09, 2009 | Dewalt DC925B Heavy Duty Xrp 18V Cordless...

1 Answer

Shake the drill to make it work


Sounds like the battery is not making a good connection inside the drill handle. Clean the contacts inside the handle where the battery plugs. Clean the contacts on the battery. If there are any springy tabs in either of these places, pry them up slightly to increase the pressure between the contacts.

Clean with wire brush, sandpaper, electrical contact cleaner.

If this doesn't work, get back to me and we'll go to the next step.

Charlie

May 09, 2009 | Dewalt DC925 Cordless Drill

2 Answers

Shake the drill to make it work


I just replaced the switch assembly for the same problem

Jan 12, 2008 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

Not finding what you are looking for?
Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Logo

442 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

79865 Answers

Jim Thurston

Level 3 Expert

672 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...