Question about Computers & Internet

1 Answer

Video Monitor goes black and comes back within a few seconds. Message :display driver failed and recovered.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,601 Answers

Take out older drivers and then re-install new drivers. They apparently are corrupted.

Posted on Jan 12, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My all in one vaio , keeps going to black screen, fans still going round

please check power cable of this computer if everything is correct then you need to contact with local technician.. it might be hardware problem..


Oct 09, 2014 | Sony VAIO Computers & Internet

1 Answer

My AOC screen goes black after about a few seconds after booting.


The picture board on your monitor is bad, since it goes off after few seconds and the power led or button is on, it means the picture board of your monitor has developed fault.

The best thing for you to do now is to take the monitor to a local repairer or service center within your vicinity to help with the replacement of the picture board because the fault is not something you can fix yourself, in order not to complicate issues.

Take care.

Jul 26, 2010 | AOC LM729 17" LCD Monitor

1 Answer

Display driver stopped responding and successfully recovered

try checking for updated drivers for your hd 5730. i have seen this in desktops with both ati and nvidia gpus.

Jun 21, 2010 | Alienware PC Systems Alienware m15x Gaming...

1 Answer

Proview Monitor PL926 Wbi The power indicator

Repair estimate will be according to problem.

Nov 13, 2009 | Proview PL926WBi 19" LCD Monitor

1 Answer

Monitor displays the PC screen but switches off within 10 second

Unfortunatley your monitor is going out. I just had that problem. My sceen would come on, but after about 10min. it would blink off and turn black. I would have to hit the off button on the monitor, then turn it back on. It would work fine for a few minutes then black out again. I got a new/used monitor where I no longer have that problem.

I did check to make sure my hybernate was not activated, it wasn't, I had it set to never turn off.

Good luck.

Sep 02, 2009 | Rosewill R900J 19" Flat Panel LCD Monitor

1 Answer

Screen goes blank after a few seconds

Hi ,
The monitor flicker problem. The monitor when turn on will display image for couple of second then turn black. The monitor status led is still green. This will happen each time it is turn on. The symptom at appear to come from the inverter board.

May 08, 2009 | NEC-Mitsubishi NEC Display Solutions...

1 Answer

LCD monitor goes blank

It appears that the display resolution set in your display properties is out of the range that the LCD can display.

Try this.

Boot to the ENABLE VGA MODE by pressing F8 to get the Windows Boot Menu. If you can get to the desktop, then go to display properties, and see if you can change the resolution to higher settings and maintain video. (If the video blanks out, then it should revert to the previous setting in 15 seconds)

Aug 03, 2008 | Gateway FPD2275W LCD Monitor

4 Answers

No Image but power

find the manufature of the video card, use the old monitor and go to the video card manufacture and download the video driver.

Jun 30, 2008 | Philips 170B4MG 17" LCD Monitor

1 Answer

Computer monitor comes on for 1 seconds, flashes "analog power save mode" and then goes black.

Most monitors will say "Power save mode" when they can tell through residual voltage that the signal lead is plugged into a machine, but there's no picture being transmitted. The four states of a monitor are:

* Off entirely.
* Switched on, plugged into a computer but no video signal being received - usually displays "analog power save mode" or "digital power save mode" for a few seconds, then blanks. Comes back to life the moment a video signal is received. This state is the default in full power saving mode.
* Switched on, not plugged into a computer. Some monitors don't display anything, some go into power saving mode, some fly "CHECK SIGNAL CABLE" or a similar message around the screen. Picture is restored when the signal cable is plugged back into the computer
* On fully, receiving an image, and displaying.

Hope this helps.

Jun 01, 2008 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides