Question about Hoover AL120 Front Load Washer

1 Answer

Wont Stop I have an AL120 Hoover Washing Machine that wont stop at end of most cycle programs, program knob just keeps on going? Have to stop it manually

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 236 Answers

Probably the timer pcb has gone faulty.

Posted on Feb 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hoover 500mb 5.0kg washing machine fills up fine at start of cycle then just washes for a bit then just stats to fill up and wont stop till I stop it


I had a similar problem and not sure whether my solution would help you.It was to do with the position of the waste pipe.It should raised about 2ft. ,looped before discharged into the washing machine tee.when the discharge hose is lying on the floor there's a possibility that the water is filling up and going straight out.By raising it you are letting it fill up and presumably triggering the water level sensor.Hope this helps.

May 29, 2017 | Hoover Washing Machines

1 Answer

My Asko washing machine wont go into spin cycle it just keeps on washing after 3 hours I had to turn it off now what


call a technician in
the problem is most likely in the program board not progressing the wash cycle

Jul 12, 2016 | Asko W6021 Front Load Washer

1 Answer

My hoover washer dryer wont start? No power


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

http://www.espares.co.uk/advice/washing-machines/a/7/1298/how-to-replace-washing-machine-controls-hotpo.html


Click for tips to repair

Jun 28, 2012 | Hoover Washing Machines

1 Answer

Hi i have an indesit w 123s washing machine, that set to any program it doesnt move on it just does that setting,then if you turn the machine off and set it to end program you can reset to rinse and the...


hello try restting it before you bin it
  1. Turn the washing machine off with the on off button.
  2. Turn the selector knob to a dot, or any off position
  3. Turn the washing machine back on and watch for rapid flashing on the neon light
  4. Turn the washing machine off and select the new program (or maybe spin)
  5. Turn it back on and the new program should start
NOTE: Resetting the timer selector knob as shown above may stop the clicking round, but if your washing machine has a fault, the clicking round may return when your washing machine encounters the fault again. If your washing machine's program selector knob is clicking round on its own, then read the section above Washing machine stops with lights flashing hope it helps

regards
shaun

Mar 13, 2011 | Indesit W 123 Front Load Washer

1 Answer

Does not stop heating water on some programs


that may be a pcb or timer problem. a short in one or more of the programs? you will need someone to have a look as it would be expensive to try changing both. sorry not more help..

Jan 07, 2011 | Hoover AL120 Front Load Washer

1 Answer

Hoover AL 120 washing machine won't spin


i would check the motor carbons it could be your problem if it fills goes through the programme until the end but has motor action

Apr 12, 2010 | Hoover AL120 Front Load Washer

1 Answer

Ariston A1635 Margherita Control knob spinning


According to the instruction book - it appears the machine has been stopped mid cycle then re-started.
Switch machine off, turn control knob to a solid circle symbol (they are after every set cycle). Switch machine back on and lights will flash and program is reset. You can then select wash cycle as normal.

Jan 22, 2010 | Ariston Technologies AW125NA 13 lbs. Load...

1 Answer

Fisher & Paykel GW703 wont stop!


It sounds like your machine has been programmed to automatically run through the various cycles continuously. Most likely in error.

Oct 07, 2007 | Washing Machines

Not finding what you are looking for?
Hoover AL120 Front Load Washer Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

shaun taylor

Level 3 Expert

1527 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...