Question about HP LaserJet 1022 Printer

1 Answer

No lights. Have power

The cables are fine. Both work with my other printer. my New, out of the box HP 1022 has no lights. It powers up when I plug it in, but no lights and will not do a test print or print from the computer. Ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 417 Answers
Re: No lights. Have power

If it is out of the box then take it back to the store for and exchange the likely thing is that the memory has fallen out and not allowing the machine to boot up correctly. But I suggest take it back for a exchange.

Thanks J

Posted on Jan 14, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

HP Laserjet 1022 orange light keeps flashing

1. Check any paper jams in side.
2. Check cartridge.
3. Remove back cover, clean paper sensors.
4. Replace Formatter board.

Jan 05, 2013 | HP LaserJet 1022 Printer

4 Answers

Hp laserjet 1022

did you try to uninstall the existing driver and reinstall the latest one ?

Aug 15, 2008 | HP LaserJet 1022 Printer

1 Answer

HP laser Jet 1022 only prints one page at a time

Jan 2013 Installed this new printer driver and all my HP 1022 problems disappeared; now printing perfectly back as usual!
HP Printer Drivers v.2.13 for OS X
Click on the link above or copy and paste the following address into your Web browser to view the article:<>

Mar 05, 2012 | HP LaserJet 1022 Printer

1 Answer

After powering on printer firstly initialize then all led are turn on & not getting ready...

c00381709.gif Fatal error

All lights are on. Unplug the printer for 30 minutes, and then plug the printer back in power outlet.

Replace the formatter assm..

Oct 08, 2011 | HP LaserJet 1022 Printer

1 Answer

My HP Photosmart C4480 was working fine last time I used it, but now the mini-display isn't lighting up, the power light is blinking on and off, and my laptop says the printer is "offline". What do I do?

HP photosmart C4480 power on but screen blank and nothing flashing - keeps asking to connect usb cable, this has been checked and new cable tried but still not working

Sep 22, 2009 | HP Photosmart C4480 All-In-One InkJet...

1 Answer

My 2350 all in one will not turn on.

I'm not sure if this is a solution, but it worked for me. ( who knows how long it will last, but its working for now)

Below are the steps I took:

- uninstalled all the HP drives and software
- unplugged the USB cable from the computer and printer
-unplugged power supply from the outlet and printer
-plugged the USB back in to computer and printer
-unplugged the power supply from the power module. Made sure everything looked ok,
-reattached power supply cord to module ( Made sure everything looked ok,)
-plugged power supply in to outlet ( green light was on)
-proceeded to plug power module connector to printer. ( again, making sure proper connection was made.

* this time the screen came with an error and the "on" power light was blinking.:
This was the error message:



-I proceeded to unplug the power and usb from the printer
-downloaded the lastest drivers and software for the PSC 2350
-After the software was loaded and installed ( I checked the box to install with out USB communication at this point)
- plugged the power and then the USB.
-It came to life at that point. (the computer recognized the "new" product)Going through what I presume were several realignments or internal configurations.

I tested a page, and ran the HP Dinostic's page. Everything checked out, and its running fine for now.

I hope this may have given you some ideas as to fixing your printer.

Feb 14, 2009 | HP PSC 2350 All-In-One InkJet Printer

1 Answer

HP 1022 Laserjet Feed Problem?

Try to cold reset you printer

Power off the printer.
* Power on the printer while pressing both the Go and Cancel buttons.
* Keep the buttons pressed. The lights will begin to flash in sequence.
* Release the buttons when all three lights begin to flash in union.

Printer is now reset

Try to send a test print now

Keep me posted!


Nov 13, 2008 | Printers & Copiers

1 Answer

I think I killed my HP L7580 printer... Powers up, but does not respond


Not neccesarily.. the voltages are different for each printers power supply. is it a power cable with a little black box on it? or just a straight power cable to the wall?

The 2510 may have a diferent voltage.. you can tell by looking on the bottom of the black box and see what the OUTPUT is.. is they're different.. time to go shopping

Best Wishes

Sep 25, 2008 | HP Officejet Pro L7580 All-In-One InkJet...

2 Answers

HP Laserjet 1022

on the back side thers are two papers sensors inside the printer,they get stucked,normally they should come back

Jan 23, 2008 | HP LaserJet 1022 Printer

2 Answers

All lights on

Fatal error, I think it has gotten rid of itself, probally fuser at cheapest would be the fix and even that would be more than it is worth to fix. Fatal error will be fuser/laser/board all cost in parts min $100 to 350.

that great but now how do i get rid of it? Place in bin after releasing frustration apon it, if not under warranty

Dec 13, 2007 | HP LaserJet 1022 Printer

Not finding what you are looking for?
HP LaserJet 1022 Printer Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts


Level 3 Expert

93729 Answers


Level 3 Expert

7983 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides