Question about Toshiba 2060 Copier

1 Answer

Lcf We are band aides and the LCF needs to be released. What is it and where can u find it?????? plz help!

Posted by on

1 Answer

Re: lcf


Posted on Jan 15, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Misfeed in copier and total counter 463898

Your information too general. But base on your meter reading counter, I assumed a lot of your copier's parts might worn out.
1) Check any paper jammed remaining in the copier. You might accidentally tore the paper and the other tore remaining paper still in the copier.
2) Open and close all the covers. its all on the right side.
-fuser cover,side cover (T/S block section), duplex cover, drawer 1 cover (just below bypass), optional drawer cover (if there is LCT or LCF)
2) Replaced the feed, separation rollers for the drawers,
3) Check the fuser condition. Replace them if condition is not good.

Mar 08, 2015 | Toshiba e-Studio 350 Copier

1 Answer

Toshiba e233 photocopier does not coincide with the top margin of the original copy

Top margin??? SEF or LEF

1. If it is the lead edge registration, go to 05 mode and adjust the values of the following...

440 > start > adjust value (for upper drawer margin)
441 > start > adjust value (for lower drawer margin)
442 > start > adjust value (for bypass drawer margin)
443 > start > adjust value (for LCF)

2. If it is the side registration, adjust it from the drawers.

Nov 30, 2012 | Printers & Copiers

2 Answers

Canon ir 5000 showing paper jam in leht hand LCF but no paper at this point or any where else

two possibilities...

feed rollers are worn out... replace them...
or paper wadded up in lcf
or another possibility... bad sensor or dirty sensor...

Aug 13, 2011 | Printers & Copiers

1 Answer

When i switch on my photocopier tohiba 2860, it asks for service and gives an error code 08221-918100. what could be the problem?

Hi tkasirye,

Welcome to Fixya.

You may need to check again the error code. According to the manufacturer's checklist for error codes, only the following are documented;

  1. Error Codes - Toshiba 2860

  1. "E01" Paper jam inside machine. "E02" Paper jam near the fuser. "E03" Paper jammed inside machine when power supply is switched on. "E04" Front cover open while copying. "E05" Paper jam near the aligning roller "E08" Paper jam at stacking area in the ADU "E11" Paper feeding jam at the ADU "E12" Manual feeding jam "E13" Paper jam from cassette 1 "E14" Paper jam from cassette 2 "E15" Paper jam from cassette 3 "E16" Paper jam from cassette 4 "E17" Paper jam from cassette 5 "E19" Paper jam from the LCF "E21" Paper jam in transport route 1 (LCF) "E22" Paper jam in transport route 2 (COPIER) "E23" Paper jam in transport route 3 (ALIGNING) "E25" Paper jam in transport route 4 (PFP) "E71" Original feed jam in ADF "E72" Original transporting jam in ADF "E73" Original exiting jam in ADF "E75" 2nd original feeding jam "E81" Paper jam before sorter "E82" Paper jam in sorter "E83" Sorter early arrival jam "E84" Paper in sorter when power is turned on "E85" Joint open jam while copying "E88" Paper jam outside the sorter bin "C01" Abnormal operation of the copier main motor "C04" Abnormal operation of the PFP main motor "C05" Abnormal operation of the ADU main motor "C11" Abnormal operation of the ADU side motor "C12" Abnormal operation of the ADU end motor "C13" Abnormal operation of the upper cassette tray "C14" Abnormal operation of the lower cassette tray "C15" Abnormal operation of the PFP upper cassette tray "C16" Abnormal operation of the PFP middle cassette tray "C17" Abnormal operation of the PFP lower cassette tray "C18" Abnormal operation of the LCF tray "C21" Optics carriage initialize error "C22" Lens initialize error "C23" Mirror initialize error "C26" Faulty exposure lamp "C33" Easy set-up is failed "C35" Developer material exists at the transfer separation adjustment "C41" Faulty thermistor or heater "C43" Faulty thermistor "C44" Faulty heater "C45" Sub thermistor is open
Shoulg you not find any of these mentioned error codes, I suggest you contact the tech support especially if the machine is still under warranty.

Hope this helps.


Jul 05, 2011 | Toshiba Printers & Copiers

1 Answer

C-1120 on a CS 5035

The LCF lift 1 is not working

Jun 10, 2011 | Kyocera Copystar CS-5035 Copier

3 Answers

Call for service error in Toshiba studio 160

Code Description C01 Main motor drive error C04 PFP main motor drive error C06 LCF feed motor error (DP2000/2500 series) C13 Cassette 1 error C14 Cassette 2 error C15 Cassette 3 error C16 Cassette 4 error (DP2000/2500 series) C18 LCF tray error (DP2000/2500 series) C19 LCF feed motor abnormal (DP2000/2500 series) C21 Carriage initialization error C25 Scanner unit watch dog error C26 Exposure lamp disconnection or peak detection error C38 Replaced process unit error C41 Abnormal thermistor or heater disconnection at power ON C43 Warming up mode after disconnection judgment, or abnormal thermistor after ready C44 Warming up mode after disconnection judgment, or heater abnormal after ready C45 Thermistor disconnection at the end part of heater C56 Communication error between PFC and main unit C57 Communication error between main unit and IPC (DP2000/2500 series)

May 22, 2011 | Toshiba E-Studio 160 All-In-One Laser...

1 Answer

Release LCF... ??

Look on page 115 of this users guide to release MP-1501 (LCF). If you are refering to release as in remove from machine, that's a we bit more involved. Let me know if the later is what you're looking to accomplish.

Sep 21, 2009 | Toshiba 2060 Copier

1 Answer

Giving 954 nvram card error

this is an error that will return you can reset it sometimed hold the right arrow select and go buttons down and power the unit on. when you see action in the display release the buttons. if the nvram has any uncorrupted space left on it the nvram will be relocated to that spot. this is only a band aid and the engiine board needs to be replaced

Apr 06, 2009 | Lexmark Optra T612 Laser Printer

1 Answer

E3co e3eo toshiba 451c

E3C0 indicates LCF transport jam (not reaching the registration sensor).

Open the jam access cover. Is there paper in front of the registration sensor?
YES-> Remove the paper.
NO->Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E])

If NO ,
1) Check if the connector of the registration sensor is disconnected.
2) Check if the connector CN338 on the LGC board is disconnected.
3) Check if the connector pins are disconnected or the harnesses are open
4) Check if the conductor pattern on the LGC board is short circuited or open
5) Replace the registration sensor.
6) Replace the LGC board.

Are the upper transport clutches (high/low speed) working?
(Perform the output check: 03-439, 440)

Feb 10, 2009 | Toshiba E-Studio 3511 Color Copier

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Printers & Copiers Experts

Anthony Chiang
Anthony Chiang

Level 3 Expert

524 Answers

Michel Smith

Level 3 Expert

1218 Answers


Level 3 Expert

1113 Answers

Are you a Toshiba Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides